Tractel Davimast Manuel D'installation, D'entretien Et D'emploi page 16

e. The lo o
ide ti catio
responsible for production inspection;
f. The batch number;
GB
g. The serial number;
h. A pictogram showing that the manual must be read
before use;
o. The minimum breaking strength of the anchor
device;
p. The number of individuals: One or two operators
maximum depending on the bracket;
w. The maximum working load;
aa. The date of the next periodic inspection;
ae. ate o rst use a d
af. Anchor device against falling of persons.
1 2 . e io ic in pection an
A a ual periodic i spectio is ma datory howe er,
depe di o the re ue cy o use, e
conditions and regulations of the company or the
cou try o use, periodic i spectio s may
re ue t.
this e uipme t is dirty, wash it with clea a d cold
water with a synthetic brush. During transport and
stora e, protect the e uipme t i
packa i rom a y ha ards
chemical products a d
Periodic i spectio s must e carried out y a uali ed
technician in strict compliance with periodic inspection
procedures.
o rmi the le i ility o the product marki
integral part of the periodic inspection.
The outcome of these inspections must be recorded
in the inspection register located at the centre of these
i structio s, which must e kept throu hout the li e o
the product until it is taken out of service.
The technician must also complete lines A to E of the
table with the following information:
A: Name of inspector;
B: Date of inspection;
C: Inspection result OK/Not OK;
D: Signature of inspector; and
E: Date of next inspection.
A ter arresti a all, this product must u der o a
periodic inspection as described in this section.
The Davimast Blocfor™
supplied with their e uipped system, so it is ad isa le
to carry out periodic visual inspections on the brackets
and their respective system.
16
ollowed y the um er 0082,
um er o the oti ed
epai
iro me tal
moisture resista t
direct heat source,
li ht, etc. .
R and Carol™ TS brackets are
1 2 .1 . ec in t e avi a t
ody
1 2 .1 .1 . ec in t e
The bracket must have the following markings at least:
• The manufacturer's or supplier's name;
• The e uipme t re ere ce
• The batch or serial number;
• The e uipme t sta dard ollowed y the year o
reference; and
• The logo; read the instruction manual.
NOTE:
e uipme t must e take out o ser ice.
1 2 .1 .2 . ec in t e co p l o
p e ent
The Davimast must have the following at least:
• Two pins;
• Two safety pins connected to the bracket by means
of a cablet; and
e more
• One rotation ring.
1 2 .1 .3 . ec in t e ene al con ition o t e
avi a t
spect each side o the a imast a d more speci cally
check whether:
• The tube is deformed;
• The mounting holes are deformed in any way;
• The pins and safety pins are deformed in any way;
• There is any corrosion;
• The mast rotates freely in a base plate; and
• The retaining stop is present on the rotating ring.
s is a
NOTE: Non-compliance with the above check
does ot ecessarily mea
decommissio ed,
until it has been repaired by Tractel or an authorised
repairer.
1 2 .2 . ec in t e ca le
Always wear protective gloves and goggles when
checking the cable.
This chapter describes the procedure for checking a
Tractel cable for the Blocfor™
®
All cables are supplied with a connector.
The fastening loop must never be a simple knot or lock
with cable clamps or a splice.
Position the cable so that it can be inspected along its
entire circumference and length.
a in
a y marki oes missi
co ponent a e
the e uipme t is to
ut the de ice must
and Carol™
, the a ected
e
ot e used
brackets.