Chamberlain MotorLift RA10 Instructions page 11

IMPORTANT SAFETY RULES - SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS FOR THE
USER
Caution! Non-compliance can result in serious
injury.
Any work on the electrical installation including
servicing may only be performed by a qualified
electrician.
Do not allow children to play with the controls.
Check shutter or sun-blind system regularly for
signs of wear and damage. Damaged systems
should not be used under any circumstances
until such time as they have been repaired.
Observe shutter or sun-blind system carefully whilst
in operation.
Switch off shutter or sun-blind system and
disconnect from mains supply, if any servicing
or cleaning has to be done either on the system
itself or in its immediate vicinity.
Ensure that the motor is accessible after installation.
Ensure sufficient room (at least 40 cm) is left
between any moving parts and nearby objects.
Ensure system cannot trap or cut persons and
secure relevant parts.
Correct use
Type RA10 - RA50 tubular drives are designed for the exclusive
purpose of operating shutters and sun-blind systems.
In compliance with standard EN 60 335-2-97:2000, the cable
connecting the RA10 drive to the mains cable must be laid
internally.
EJOT Delta PT 40x12 WN 5454 Torx (9900 000 545 4) is the
only type of screw that can be used to fasten the connecting
parts to the RA10 motor.
Any other form of usage is deemed to be incorrect. Neither the
manufacturer nor the supplier assumes any liability for personal
injury, damage to property or consequential injury or damage
occurring as a result of the use of the control units and / or
drives for purposes other than those mentioned above or due
to changes made to the equipment affecting the safety of the
given system.
The details stipulated in the Operating Instructions in respect of
the operation and repair of the system require strict
observance. Neither the manufacturer nor the supplier
assumes any liability for personal injury, damage to
property or consequential injury or damage occurring as a
result of non-compliant actions.
IMPORTANT SAFETY INSTRUCTIONS FOR THE
FITTER
Caution! Non-compliance can result in serious
injury. Observe EN 60 335-2-97:2000 Safety
Instructions in full.
Any work on the electrical installation may only be
performed by a qualified electrician.
When electrical or electronic systems and
appliances are in operation, certain components
are live, which can constitute a risk. Any touching of
and work performed on the equipment by persons
not qualified to do so or non-compliance with safety
instructions can result in personal injury or damage
to property.
All the standards and regulations applying to
electrical installations must be observed.
Only those spare parts, tools and other equipment
as have been approved by Chamberlain may be
used.
Neither the manufacturer nor the supplier assumes
any liability for personal injury, damage to property
or consequential injury or damage occurring as a
result of the use of non-approved third party
products or changes made to any accessories.
Prior to performing installation work, de-activate all
connections and control facilities that are not
absolutely essential for operation of the given
system.
Fit control facilities within sight of the product to be
controlled at a height of at least 1.5 m.
Ensure sufficient room is left between any moving
parts and nearby objects.
Torque rating and duty cycle must comply with the
requirements of the product to be driven
Technical data - torque rating and duty cycle details
can be found on the tubular drive's data plate.
Ensure system cannot trap or cut persons and
secure relevant parts.
Observe safety margins as stipulated in DIN EN 294.
Please consult Chamberlain product information for
further details.
Declaration of Conformity
Tubular Motor.................................................................RA10 -RA20 - RA30 - RA50
is in conformity to the applicable sections of Standards ..EN55014, EN610003, ETS RES 0908,
per the provisions & all amendments
of EU Directives...........................................................73/23/EEC, 89/336EEC
Declaration of Incorporation
Tubular Motor Model RA10, RA20, RA30 and RA540, when installed and maintained
according to all the Manufacturer's instructions in combination with a shutter which has
also been installed and maintained according to all the Manufacturer's instructions, meets
the provisions of EU Directive 89/392EEC and all amendments.
I, the undersigned, hereby declare that the equipment specified above and any
accessory listed in the manual conforms to the above Directives and Standards.
Chamberlain GmbH
D-66793 Saarwellingen
March, 2002
EN60555, & EN60335-1
Colin B. Willmott
Chief Engineer