Maintaining The Equipment; Storing The Equipment; Electrical Connection - Scheppach HS110 Traduction Des Instructions D'origine

13. Maintaining the equipment

m WARNING! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
13.1 General maintenance measures
• Keep protective devices, air vents, suction openings
and the motor housing as free of dust and dirt as
possible. Remove shavings and dust with a vacu-
um cleaner and a brush. In addition, blow it out with
low-pressure compressed air.
• We recommend that you clean the equipment imme-
diately after you use it.
• Clean the equipment regularly with a damp cloth and
some soft soap. Do not use cleaning agents or sol-
vents; these may be aggressive to the plastic parts
in the equipment. Ensure that no water can get into
the interior of the equipment.
• In order to extend the service life of the tool, oil the
rotary parts once monthly. Do not oil the motor.
13.2 Replacing the table insert (fig. 13)
m WARNING: In the event of wear or damage the ta-
ble insert (5) must be replaced; otherwise there is an
increased danger of injury.
1. Remove the two countersunk head screws of the
table inlay (25) using a Phillips screwdriver (not in-
cluded in the scope of delivery).
2. Remove the worn table inlay (5).
3. Installation of the new table inlay takes place in
reverse order.
13.3 Carbon brushes
In case of excessive sparking, have the carbon brush-
es checked only by an electrical specialist. IMPOR-
TANT: The carbon brushes must not be replaced by
anyone but an electrical specialist.
13.4 Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consum-
ables.
Wear parts*: Carbon brushes, saw blade, table inlays,
push stick
* Not necessarily included in the scope of delivery!
Spare parts and accessories can be obtained from our
service centre. To do this, scan the QR code on the
cover page.
46 | GB

14. Storing the equipment

Store the device and its accessories in a dark, dry and
frostproof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.

15. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions. The cus-
tomer's mains connection as well as the extension
cable used must also comply with these regula-
tions.
• The product meets the requirements of EN 61000-
3-11 and is subject to special connection conditions.
This means that use of the product at any freely se-
lectable connection point is not allowed.
• Given unfavorable conditions in the power supply
the product can cause the voltage to fluctuate tem-
porarily.
• The product is intended solely for use at connection
points that
a)do not exceed a maximum permitted supply im-
pedance "Z" (Zmax. = 0,429 Ω), or
b) have a continuous current-carrying capacity of
the mains of at least 100 A per phase.
• As the user, you are required to ensure, in consulta-
tion with your electric power company if necessary,
that the connection point at which you wish to oper-
ate the product meets one of the two requirements,
a) or b), named above.
15.1 Important information
In the event of an overloading the motor will switch it-
self off. After a cool-down period (time varies) the mo-
tor can be switched back on again.
15.2 Damaged electrical connection cable.
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors
• Kinks where the connection cable has been improp-
erly fastened or routed
www.scheppach.com