Scheppach HS110 Traduction Des Instructions D'origine page 41

9.1 Assembling the frame and table width exten-
sion (fig. 4-10)
1. Turn circular table saw upside down and place on
the floor.
2. Fasten the table width extension (6) loosely onto
the saw table (1) with the hexagonal bolts (a), the
washers (c), the spring washers (d) and the nuts
(e) (fig. 6).
3. The four legs (19) are screwed to the housing to-
gether with the table supports (24) (fig. 7).
4. Fasten the table supports (24) loosely to the table
width extensions (6) with the hexagonal bolts (a),
the washers (c), the spring washers (d) and the
nuts (e). Loosely tighten the legs (19) and the table
supports (24) onto the housing of the circular table
saw with the hexagonal bolts (a).
5. Now screw the four centre struts (20a, 20b) loose-
ly onto the legs (19). Use the coach bolts (b), the
washers (c), the spring washers (d) and the nuts
(e) (fig. 8).
6. Screw on the stands (22) at the holes in the rear
legs (19). Assembly materials: 2 coach bolts (b),
the washers (c), spring washers (d) and nuts (e)
respectively (fig. 9).
ATTENTION: Both stands must be fastened to the
fastening points (23) on the rear of the machine
(fig. 9).
7. Align the table width extension (6) level with the
saw table.
8. Now tighten all screws for the legs (19) and the
table width extension (6).
9. Now plug the rubber feet (21) onto the legs (19)
(fig. 10).
10. Place the circular table saw on the machine stand
(11).
9.2 Fitting the guide rail (fig. 11+12)
1. Fit the coach bolts (b) in the respective drilled
holes in the work table and the table extensions
(6), by securing these from the rear with the flange
nuts (e).
2. Tighten the flange nuts (e) lightly.
3. Connect the two guide rails (15, 15a).
4. Slide the connected rails over the guide nut on the
rear, over the coach bolts (b), until they sit central
to the table surface.
9.3 Aligning the guide rail (fig. 11+12)
1. Turn the saw blade to the maximum position out of
the saw table, by turning the crank (10) clockwise
until it reaches the stop.
2. Position the parallel stop with an opened eccentric
lever (13) on the guide rails (15) on the saw table
and secure these in the 0 position by pressing the
eccentric lever (13) fully downwards.
3. Slide the connected guide rails sufficiently far to
the left, until the parallel stop reaches the right out-
side of the saw blade.
4. Now tighten the flange nuts (e) firmly to fix this po-
sition.
5. Now fit the end caps (15b) on both sides of the rail.
9.4 Fitting/removing the saw blade guard
(fig. 13+14)
1. Loosen the screw with nut and washer (27) of the
saw blade guard (2). Place the saw blade guard (2)
onto the riving knife (3) from above.
2. Fit the screw with nut and washer (27) such that
the screw sits firmly in the elongated hole.
3. Do not over-tighten the screw (27). The saw blade
guard must remain free to move.
4. Disassembly takes place in reverse order.
m WARNING: Before starting sawing, the saw blade
guard (2) must be lowered onto the material to be sawn.
After fitting, check that the saw blade guard (2) is func-
tioning properly. Lift the saw blade guard and then
release it. The saw blade guard should automatically
move back to its starting position.
9.5 Mounting / adjusting the Riving Knife
Insert the battery (Fig. 13-16)
Attention! The riving knife is in the transport posi-
tion. Before operating the product it must be set to
working position first!
Caution! Remove the mains plug! The setting of
the saw blade (4) must be checked whenever a
blade has been replaced.
1. Inserting the batteries (Figure 13a):
- Turn the laser on/off switch (34) to the 0 position
(laser off).
- Remove the battery compartment cover (36), by
loosening the screw (35). Now remove the battery
compartment cover (35) by bending at the side.
- Insert the batteries supplied (type AAA), ensuring
the correct polarity (see Figure 13a).
- Put the battery compartment cover (36) back in
position and tighten it with the screw (35).
www.scheppach.com GB | 41