Nice Riva Instructions Et Avertissements Pour L'installation Et L'utilisation page 63

TECHNICAL SPECIFICATIONS OF PRODUCT COMPONENTS
RIVA200 is manufactured by NICE S.p.A. (TV) Italy. Nice S.p.A., in order to improve its products, reserves the right to modify their technical
characteristics at any time without prior notice. In any case, the manufacturer guarantees their functionality and fitness for the intended purposes.
Note: all the technical characteristics refer to a temperature of 20°C.
Model
Type
Technology adopted
Peak torque
Nominal torque
Speed (no load)
Nominal torque speed
Maximum cycles frequency
Maximum continuous cycle time
Operating limits
Power input
Nominal absorbed current
Ambient operating temperature
Mounting
Protection rating
Dimensions / weight
CL201 command control unit
Type
Technology adopted
Maximum cycles frequency
Maximum continuous cycle time
Mains power supply
Nominal absorbed power
Emergency power supply
Motors output
Flashing light output
ECSbus output
"SbS" input
"STOP" inputv
Radio Antenna input
Maximum cable length
Ambient operating temperature
Mounting
Protection rating
Dimensions / weight
Remote control compatibility
Memorisable ECCO5... transmitters
RIVA200
Electromechanical gearmotor for automation of automatic gates and doors
24 V motor, reducer with helical gears; mechanical release
250 Nm
120 Nm
1.25 RPM
1 RPM
60 cycles/hour
10 minutes
The structural features make it suitable for use on gates with a weight of up to 200 kg or a
leaf length of up to 2.3 m and an opening angle of up to 180°
24 V
2A, at peak power the maximum current is 5 A for a maximum duration of 2 s
-20°C ... 50°C (at low temperatures the gearmotor efficiency decreases)
Interred in a suitable foundation excavation
IP67
230 x 206 x h 88 mm / 15 kg (gearmotor with foundation case)
Command control unit for 1 or 2 24 V
doors, complete with radio receiver for "ECCO5..." transmitters
Electronic board governed by an 8 Bit microcontroller with flash technology
A transformer inside the control unit, but separated from the board, reduces the mains volt-
age to the nominal 24V voltage used in all of the automation system
15 cycles/hour at 50°C
5 minutes
230V (+10% -10%) 50/60Hz
170W; at peak the power is 360W for a maximum duration of 2s
Provision for "PR100" buffer battery connection
2, for 24 V motors with a nominal current of 2A, at peak power the maximum current is
5 A for a maximum duration of 2 s
For flashing lights with 12 V (maximum 21 W) bulb
One output with maximum load of 15 ECSbus units (1 ECSBus corresponds to the con-
sumption of a pair of photocells)
For normally open contacts (the closing of the contact causes the "Step-by-Step or Pedes-
trian Opening" command)
For normally closed or normally open contacts and/or for constant resistance of 8.2 KΩ, or
normally closed contacts with self-recognition of the "normal" state (any variation from the
memorised status causes the "STOP" command).
50 Ω for RG58 or similar type of cable
Mains power supply: 30 m; motors outputs: 10 m; other inputs/outputs: 20 m with antenna
cable preferably shorter than 5 m (observe the warnings regarding minimum gauge and
type of cables)
-20°C ... 50°C
Vertical, wall-mounted
IP44
180 x 240 h 110 mm / 2.8 kg
Using "ECCO5..." transmitters, the control unit is able to receive one or more of the follow-
ing commands: "Step-by-Step", "Partial Open", "Open Only" and "Close Only"
Up to 150 if memorised in mode 1
motors for automation of automatic gates or
English – 29