Introduction; Device Description; Scope Of Delivery; Proper Use - Scheppach TIGER 2500 Mode D'emploi

2. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
we hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device.
The operating instructions are intended to help the
user to become familiar with the machine and take
advantage of its application possibilities in accord-
ance with the recommendations.
The operating instructions contain important informa-
tion on how to operate the machine safely, profes-
sionally and economically, how to avoid danger, cost-
ly repairs, reduce downtimes and how to increase
reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country.
Keep the operating instructions package with the
machine at all times and store it in a plastic cover to
protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information. The machine can only
be operated by persons who were instructed con-
cerning the operation of the machine and who are in-
formed about the associated dangers. The minimum
age requirement must be complied with.
In addition to the safety instructions contained in this
operating manual and the specific regulations of your
country, the technical rules generally accepted for the
operation of machines of the same type must be ob-
served.
We accept no liability for damage or accidents which
arise due to non-observance of these instructions
and the safety information.
18 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

3. Device description

1. Workpiece support
2. Upper mount, workpiece support
3. Star grip screw
4. Leather honing wheel
5. Machine housing
6. On/off switch
7. Rubber feet
8. Water tank
9. Washer
10. Grinding shaft
11. Nut
12. Grindstone
13. Fixture for chisel
14. Star grip screw for leather honing wheel
15. Side mount, workpiece support

4. Scope of delivery

1 Wet grinding machine
1 Grindstone
1 Universal holder
1 Angle gauge
1 Honing compound
1 Leather honing disc
1 Operating manual

5. Proper use

m The wet grinding machine is constructed ex-
clusively for use with the tool offered for grinding
steel (no carbide).
• The machine complies with the applicable EC ma-
chinery directive.
• The machine is designed for single-shift opera-
tion, duty cycle S1 100%.
• Observe all safety information and danger notices
on the machine.
• Ensure that all of the safety information and danger
notices on the machine are complete and in legible
condition.
• Only use the machine when in a technically fault-
less condition, appropriately and in compliance
with the operating manual and with full knowledge
of safety and hazards! In particular, rectify malfunc-
tions that could impair safety immediately (or com-
mission rectification works accordingly)!
• The manufacturer's safety, operating and main-
tenance specifications as well as the dimensions
given in the technical data must be observed.
• Relevant accident prevention regulations and other
generally recognized safety and technical rules
must also be observed.
• The machine may only be used, maintained or
repaired by trained persons who are familiar
with it and have been informed of the dangers.
Any liability of the manufacturer for damages re-
sulting from arbitrary changes to the machine is
excluded.