Introduction; Device Description; Scope Of Delivery - Scheppach 5903405901 Traduction Des Instructions D'origine

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non­compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due
to the non­compliance of the electric regulations and
VDE regulations 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating in­
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operat­
ing instructions contain important information on how
to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, re­
duce downtimes and how to increase reliability and
service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula­
tions that apply for the operation of the machine in
your country. Keep the operating instructions pack­
age with the machine at all times and store it in a
plastic cover to protect it from dirt and moisture. Read
the instruction manual each time before operating the
machine and carefully follow its information. The ma­
chine can only be operated by persons who were in­
structed concerning the operation of the machine and
who are informed about the associated dangers. The
minimum age requirement must be complied with.
In addition to the safety requirements in these operat­
ing instructions and your country's applicable regula­
tions, you should observe the generally recognized
technical rules concerning the operation of wood­
working machines.
18 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
We cannot accept any liability for damage or acci­
dents which arise due to a failure to follow these in­
structions and the safety instructions.

2. Device description

1. tool spindle
2. worktable
3. ON/OFF switch
4. fixing screw
5. vacuum connector
6. cover
7. rubber sleeves
8. table inlets
9. abrasive sleeves
10. Sanding belt attachment
11. abrasive belt
12. attempt
13. Sanding belt tensioner
14. regulating screw
15. locking levers

3. Scope of delivery

• Open the packaging and remove the device care­
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
m ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swallow­
ing and suffocation!
4 x rubber sleeves
• length 115 mm, Ø 19 / 26 / 38 / 51 mm
5 x abrasive sleeves
• K80, Ø 13 / 19 / 26 / 38 / 51 mm
5 x table inlets
• Ø 13 / 19 / 26 / 38 / 51 mm
A. Locking screw ( abrasive belt)
B. Washer
C. Locking screw (stop)
D. 3 x spindle disks Ø 16 / 22 / 44 mm
E. Hexagon nut M8
F. Allen key SW13