Description, Specifications And Standard Equipment Description; Specifications; Standard Equipment - RIDGID K-380 Manuel De L'opérateur

K-380 Drain Cleaning Machine
machine. Other uses or modifying the drain cleaner for
other applications may increase the risk of injury.
Description, Specifications and

Standard Equipment

Description
The RIDGID K-380 Drain Cleaning Machine will clean
drain lines up to 4" in diameter and 75 feet in length.
Corrosion-resistant cable drum holds 100 feet of
ameter cable or 75 feet of
The drum is belt-driven by a
a grounded electrical system. An integral Ground Fault
Interrupter (GFCI) is built into the line cord and a pneumatic
foot actuator provides ON/OFF control of the motor.
The cable is manually fed in and out of the drain. An op-
tional autofeed is available that will advance or retract the
cable at a rate of 18 feet per minute. An integral torque
limiter will cause the drum to stop rotating when exces-
sive torque is created. When the cutting tool that is
attached to the cable hits a snag the drum stops rotating,
allowing the operator to relieve tension on the cable.
The integral wound cable has a quick change coupling
system for disconnecting tools. This "Solid-Core" Integral
Wound cable is a durable, kink-resistant cable.

Specifications

Line Capacity ...............Depends on choice of cable.
Refer to the following chart for
recommendations.
Cable Size
Line Size
3/8" Cable 1 1 / " – 3"
2
1/2" Cable 3" – 4"
Drum Capacity .............100' of
75' of
Motor:
Type ...........................115V/60 Hz, Reversible,
Split Phase
Rating......................... 1 /
Amps ..........................6.7
Weight (Machine Only)...37 lbs.
Length ..........................22"
25" w/Autofeed
Height ...........................22"
Width ............................15"
4
3 /
8
1 / " cable.
2
1 / HP electric motor that has
3
Recommended Line
Size & Reach
Reach
100'
75'
3 / " Diameter Cable
8
1 / " Diameter Cable
2
HP @ 1725 RPM
3
Standard Equipment
Catalog Model
No. No.
87302 K-380
87287 K-380
w/C-31 IW
" di-
84522 K-380
w/C-32 IW
87307 K-380
w/C-32 IW
87317 K-380 PF
w/C-32 IW
87327 K-380 PF
w/C-32 IW
87292 K-380
w/C-44 IW
87297 K-380
w/C-45 IW
87312 K-380
w/C-45 IW
87322 K-380 PF
w/C-45 IW
87332 K-380 PF
w/C-45 IW
Accessories
87337 A-380
59782 —
Ridge Tool Company
Description
K-380 Machine Only w/Gloves
K-380 Machine w/Gloves & Std. Equipment
– C-31 IW 3 / " x 50' Solid Core (Integral
8
Wound) Cable,
– T-260 Tool Set Includes:
– T-202 Bulb Auger
– T-205 "C" Cutter
– T-211 Spade Cutter
– A-13 Coupling Pin
K-380 Machine w/Gloves & Std. Equipment
– C-32 IW 3 / " x 75' Solid Core (Integral
8
Wound) Cable,
– T-260 Tool Set
K-380 Machine w/Gloves & Std. Equipment
– Two-Wheel Cart
– C-32 IW 3 / " x 75' Solid Core (Integral
8
Wound) Cable
– T-260 Tool Kit
K-380 Machine w/Gloves & Std. Equipment
– Autofeed
– C-32 IW / " x 75' Solid Core (Integral
3
8
Wound) Cable
– T-260 Tool Set
K-380 Machine w/Gloves & Std. Equipment
– Two-Wheel Cart
– Autofeed
– C-32 IW 3 / " x 75' Solid Core (Integral
8
Wound) Cable
– T-260 Tool Set
K-380 Machine w/Gloves & Std. Equipment
– C-44 IW 1 / " x 50' Solid Core (Integral
2
Wound) Cable
– T-260 Tool Kit
K-380- Machine w/Gloves & Std. Equipment
– C-45 IW 1 / " x 75' Solid Core (Integral
2
Wound) Cable
– T-260 Tool Set
K-380 Machine w/Gloves & Std. Equipment
– Two-Wheel Cart
– C-45 IW 1 / " x 75' Solid Core (Integral
2
Wound) Cable
– T-260 Tool Set
K-380 Machine w/Gloves & Std. Equipment
– Autofeed
– C-45 IW 1 / " x 75' Solid Core (Integral
2
Wound) Cable
– T-260 Tool Set
K-380 Machine w/Gloves & Std. Equipment
– Two-Wheel Cart
– Autofeed
– C-45 IW 1 / " x 75' Integral Wound Cable
2
– T-260 Tool Set
Auto Feed Assembly
Two-Wheel Transport Cart