Advanced Settings; Adjusting Dolby Digital Audio; Digital Output Setting - Pioneer DVJ-1000 Mode D'emploi

Advanced settings

The Setup Menu includes two mode levels, [Basic] and [Expert];
the [Expert] mode allows more advanced settings.
Audio1 V2 Language
A2 Video1
Setup Menu Mode — Expert
Setup Navigator
Basic
Parental Lock — Off (us)
Change menu mode
Move
Expert:
Displays advanced settings.
Basic:
Displays basic settings; simple explanations (
for the items selected (factory default settings).

Adjusting Dolby Digital audio

# Digital output during DJ mode is automatically converted
to linear PCM only.
This item allows adjustment of the dynamic range of digital sound.
By adjusting the audio DRC (dynamic range compression), large-
volume sounds can be attenuated and low-volume sounds can
be enhanced for a variety of playback effects. This setting is ef-
fective, for example, when it is difficult to hear dialog on a televi-
sion program, or when you do not wish to disturb neighbors while
watching movies late at night.
¶ See P.20 for menu instructions.
Audio1 A2 Video1 V2 Language
Audio DRC — Off
Dolby Digital Out On
DTS Out — Off
— 96kHz 3 48kHz
96kHz PCM Out
— MPEG 3 PCM
MPEG Out
Dynamic playback at low volume
Move
Off:
Cancels Audio DRC. Allows maximum audio presence when used
with high-fidelity speakers (factory default setting).
On:
Suppresses loud sounds (explosions, etc.) making it easier to
understand dialog.
¶ Audio DRC is supported only when using Dolby Digital audio.
¶ Some discs may produce less effect.
¶ Audio DRC is also applied to audio produced from the digital
output (coaxial) connectors. In this case, set [Dolby Digital
Out] to [Dolby Digital 3 PCM], and set [Digital Out] to [On].
¶ The effect produced with Audio DRC differs depending on
the speakers used and the volume setting of the AV amplifier.
Turn the setting ON/OFF while adjusting your sound volume
so as to produce most effective results.
General
Exit
SETUP
) are displayed
General
SETUP Exit

Digital output setting

# Digital output during DJ mode is automatically converted
to linear PCM only.
This item allows selection of the kind of digital signals supported
by the connected amplifier.
¶ If this item is set incorrectly, unwanted noise may be pro-
duced.
¶ Consult the Operating Instructions for your amplifier when
making this setting.
¶ See P.20 for menu instructions.
Dolby Digital output
Set to [Dolby Digital 3 PCM] when the connected amplifier
does not supports Dolby Digital audio.
A2
Audio1 Video1 V2 Language
Audio DRC — Off
Dolby Digital Out — Dolby Digital
Dolby Digital 3 PCM
DTS Out
96kHz 3 48kHz
96kHz PCM Out —
MPEG 3 PCM
MPEG Out —
Change Dolby Digital output mode
Move
Dolby Digital:
Setting for amplifier or decoders supporting Dolby Digital audio
(factory default setting).
Dolby Digital 3 PCM:
Dolby Digital signals are converted to linear PCM for output. Se-
lect this setting when the connected amplifier does not support
Dolby Digital audio.
DTS output
Set this item to [DTS] when the connected amplifier supports DTS.
Audio1 A2 Video1 V2 Language
Audio DRC — Off
Dolby Digital Out — Dolby Digital
DTS Out — Off
96kHz PCM Out DTS
MPEG 3 PCM
MPEG Out —
Change DTS output mode
Move
Off:
Select this item when the connected amplifier does not support
DTS (factory default setting).
DTS:
Select this item when the connected amplifier or decoder sup-
ports DTS.
96 kHz PCM output
Set this option to [96kHz] when the connected amplifier sup-
ports 96 kHz output.
Audio1 A2 Video1 V2 Language
Audio DRC — Off
Dolby Digital Out — Dolby Digital
DTS Out — Off
96kHz 3 48kHz
96kHz PCM Out —
MPEG Out 96kHz
Change 96kHz output mode
Move
96kHz 3 48kHz:
96 kHz signals are converted to 48 kHz for output. Select this
option when the connected amplifier does not support 96 kHz
signals (factory default setting).
96kHz:
Select this option if the connected amplifier or decoder supports
96 kHz output.
Preparations (Setup) Preparations (Setup)
General
Exit
SETUP
General
Exit
SETUP
General
SETUP Exit
<DRB1414> En
21