Basic Operations; Auto Cue Function; To Stop Playback; To Eject The Disc - Pioneer DVJ-1000 Mode D'emploi

Table des Matières

Les langues disponibles

Auto cue function

# This function is not supported when the rear panel NORMAL/DJ

switch is set to the NORMAL position.

This function is used to skip non-recorded (silent) portions at the begin-

ning of tracks and automatically set the cue point ( P. 36) immediately

before actual sound begins when loading a disc, performing track search

(chapter search), and when the playback track (chapter) changes. If the

track signal cannot be found within ten seconds, the track's beginning

will be set as the cue point.

I Setting auto cue ON/OFF

Hold the TIME MODE/AUTO CUE button depressed for 1 second or

more to alternate the auto cue function ON/OFF. The display's auto cue

indicator (A.CUE) lights when the auto cue function is active.

¶ The auto cue function ON/OFF status is memorized even when the

player's power is turned off.

¶ The auto cue sensitivity level can be changed if desired.

I Changing the auto cue sensitivity level

1. Hold the TIME MODE/AUTO CUE button depressed for 5

seconds or more.

¶ The display will show the "A.CUE –60dB" indicator (factory de-

fault setting).

2. Press the cursor button's left/right sides ( / ) to change

the sensitivity level.

¶ Supported sensitivity levels include: –36 dB, –42 dB, –48 dB,

–54 dB, –60 dB, –66 dB, –72 dB, –78 dB.

¶ Either press the TIME MODE/AUTO CUE button or wait 15 sec-

onds and the setting mode will be canceled and the newly se-

lected level will be set.

¶ The newly set sensitivity level is memorized even when the play-

er's power is turned off.

To stop playback

I When the UNLOCK/LOCK switch is set to UNLOCK: Press

the STOP button.

I When the UNLOCK/LOCK switch is set to LOCK: During

playback, press the PLAY/PAUSE (6) button, or if a cue

point has been set, during playback press the CUE button

to initiate back cue, then press the STOP button.

¶ When the STOP button is pressed, the current stop location will be

recorded (resume function).

¶ To resume play from the previous stop position, press the PLAY/

PAUSE (6) button.

¶ To cancel the resume function, press the DVD TITLE/MP3 FOLDER

|/\ or PREVIOUS 4/NEXT ¢ button.

To eject the disc

1. Press the EJECT (0) button when the UNLOCK/LOCK

switch is set to UNLOCK.

When the UNLOCK/LOCK switch is set to LOCK, press

the PLAY/PAUSE (6) button during playback, or when

a cue point has been set, press the CUE button (back cue)

before pressing the EJECT (0) button to eject the disc.

¶ Playback will stop and the disc will be ejected.

Resume function

¶ If the EJECT (0) button is accidentally pressed when the UNLOCK/

LOCK switch is in the UNLOCK position, immediately press the PLAY/

PAUSE (6) button to restore the unit to the mode it was in immedi-

ately prior to pressing the EJECT (0) button. However, video and

audio output will be interrupted during this interval.

¶ Following disc eject, if the same disc is reinserted, the unit will return

to the same status it was in before the disc was ejected (with excep-

tion of loop).

¶ After ejecting a disc, if the DVD TITLE/MP3 FOLDER |/\ button or

PREVIOUS 4/NEXT ¢ button is pressed the resume function

will be canceled.

¶ The resume function may not operate when playing DVDs in NOR-

MAL mode.

To temporarily interrupt playback (pause mode)

During playback, press the PLAY/PAUSE (6) button.

¶ The play/pause indicator and cue indicator will flash and play will be

interrupted.

¶ Some DVDs prohibit the use of playback pause; in this case pressing

the PLAY/PAUSE (6) button will cause the prohibited mark

light, and the corresponding prohibited mark

monitor.

¶ If the PLAY/PAUSE (6) button is pressed when the player is in the

pause (standby) mode, the play/pause indicator will light and play-

back will begin.

¶ If the pause mode is allowed to continue for 100 minutes or more,

the disc playback will automatically stop. In this case, press the PLAY/

PAUSE (6) button to resume playback.

[In DJ mode, with jog mode set to VINYL mode OFF]

¶ Placing the player in pause mode enables audible pause (the video

image appears as a still image, but audio sound can be heard inter-

mittently). If sound is not desired in this case, lower the audio mixer's

output level.

[In DJ mode, with jog mode set to VINYL mode ON]

¶ Placing the player in pause mode enables silent pause (still image

with no sound).

¶ The TOUCH/BRAKE response dial can be used to modify the disc's

deceleration speed (time until playback stops).

¶ The RELEASE/START response dial can be used to modify the disc's

playback acceleration time (time until disc reaches full playback speed).

[In NORMAL mode]

¶ Placing the player in pause mode enables silent pause (still image

with no sound).

To change language/subtitle settings

during playback (DVD only)

I To change language during playback:

The language setting can be changed during playback when the DVD

has been recorded with multiple language options.

Press the AUDIO button.

The currently selected audio (language) option will be displayed on the

screen. Each time the button is pressed the language will alternate be-

tween the available language options.

¶ If the language is changed when the player is in DJ mode, both video

and audio playback will be temporarily interrupted (due to writing to

buffer memory).

¶ Some discs do not allow the audio language option to be changed

with the AUDIO button (pressing the button will cause the prohibited

mark

to light, and the corresponding prohibited mark

pear on the screen). In this case, go to the disc's main menu to switch

the language option.

¶ When a disc is removed from the player, the language setting will

revert to that selected on the Setup Menu.

¶ With some discs, changing the language will cause the image to pause

momentarily.

I Changing the subtitle option during playback

# This option is not supported when the rear panel NORMAL/DJ

switch is set to DJ (subtitles are not displayed in DJ mode).

The subtitle language can be changed when the DVD has been recorded

with multiple subtitle language options.

Press the SUBTITLE button.

The currently selected subtitle option will be displayed on the screen.

Each time the button is pressed, the subtitle language will alternate be-

tween the available options; if OFF is selected, subtitles will not appear.

¶ Some discs do not allow the subtitle option to be changed with the

SUBTITLE button (pressing the button will cause the prohibited mark

to light, and the corresponding prohibited mark

the screen). In this case, go to the disc's main menu to switch the

subtitle language.

¶ When a disc is removed from the player, the subtitle setting will re-

vert to that selected on the Setup Menu.