Special Accessories - Gaggenau VG 414 110 Notice De Montage

Austausch der Hauptdüsen Wokbrenner (Bild 9)
Sicherungsclips an den Brennerleitungen abnehmen. Brenner-
1.
leitungen abziehen. Schraube an Luftregulierhülse lösen. Dü-
senstock abnehmen.
Düse und O-Ring für Innenkreisbrenner von Hand abziehen.
2.
Düse für Außenkreisbrenner herausschrauben (SW10).
Korrekten Sitz des O-Rings in der neuen Hauptdüse für Innen-
3.
kreisbrenner prüfen. Düse auf Brennerleitung aufschieben.
Neue Hauptdüse für Außenkreisbrenner bis zum Anschlag in
den Düsenstock schrauben.
Düsenstock und Brennerleitungen aufstecken. Sicherungsclips
4.
aufstecken.
Luftregulierhülse nach Lockern der Schraube auf das korrekte
5.
Maß einstellen (siehe Düsentabelle). Schraube wieder festdre-
hen.
Mulde auflegen und gleichmäßig festschrauben. Brennerteile
6.
und Topfträger auflegen, auf korrekte Positionierung achten.
Prüfen Sie die Funktion nach dem Umbau:
An den Flammen dürfen keine gelben Spitzen sichtbar sein.
Beim schnellen Umschalten von Groß- auf Kleinbrand darf die
Flamme nicht erlöschen.
Hinweis: Bringen Sie den Aufkleber mit der umgestellten Gasart
auf dem Typenschild am Gerät an.
en
Ú
Ins tal la tion i ns tru cti ons
Important notes
Read these instructions carefully and keep them in a safe place.
Safety during use can only be ensured if the appliance is fitted
correctly according to these installation instructions. The
installer is responsible for ensuring that the appliance operates
perfectly at the point of installation.
The appliance must be connected to the mains only by a
licensed and trained technician.
Before carrying out any type of work, turn off the electricity and
gas supply.
For installation, currently applicable building regulations and the
regulations of local electricity and gas suppliers must be
observed (e.g. Germany: DVGW-TRGI/TRGF; Switzerland:
SVGW; Austria: ÖVGW-TR).
For conversion to another type of gas, please call the after-sales
service.
: Risk of gas escape!
After connecting the appliance to the gas supply, always check
the connection for leak tightness. The manufacturer accepts no
responsibility for the escape of gas from a gas connection
which has been previously tampered with.
Ensure sufficient air exchange in the room where the
appliance is installed. Up to 11 kW total output:
Minimum volume of the room where appliance is installed:
■
20 m³
A door leading to the open air or a window which can be
■
opened.
Up to 18 kW total output:
Minimum volume of the room where appliance is installed:
■
2 m³ per kW total output.
A door leading to the open air or a window which can be
■
opened.
An extraction hood into the open air. Minimum displacement
■
volume of extraction hood: 15 m³/h per kW total output.
The installation system must incorporate an all-pin isolating
switch with a contact opening of at least 3 mm, or the appliance
should be connected to the mains via a safety plug. The plug
must remain accessible after installation is complete.
Specifications on the rating plate showing voltage, type of gas
and gas pressure must agree with the local mains connection
conditions.
Do not kink or trap the mains connection cable.
This appliance corresponds to appliance class 3 (for installation
in a kitchen unit). It must be fitted according to the installation
drawing. The wall behind the appliance must be made of non-
flammable material.
This appliance is not intended for operation with an external
timer or an external remote control.
Do not install this appliance on boats or in vehicles.

Special accessories

You can order the following special accessories from your
specialist dealer:
AA 414 010 Ventilation molding for operation next to
downdraft ventilation VL 414
WP 400 001 Multi-layer material wok pan, with curved
base and handle, Ø 36 cm, 6 litres volume,
10 cm high.
SV 401 090 Spindle extension up to 140 mm
SV 401 205 Spindle extension up to 300 mm
VA 420 000 Connection strip for combination with other
Vario 400 appliances for flush installation
VA 420 001 Connection strip for combination with other
Vario 400 appliances for flush installation
with appliance cover/extension
VA 420 010 Connection strip for combination with other
Vario 400 appliances for surface
installation
VA 420 011 Connection strip for combination with other
Vario 400 appliances for surface
installation with appliance cover/extension
VA 440 010 Stainless steel appliance cover
VA 450 400 Appliance extension, 38 cm
Only use the accessories as specified. The manufacturer
accepts no liability if these accessories are used incorrectly.
Preparing the cabinet (Fig. 1a)
The kitchen unit must be heat-resistant to at least 90°C (about
190°F). The stability of the unit must be maintained after
producing the cut-out.
Produce the cut-out in the worktop for one or more Vario
appliances as shown in the installation sketch. The angle
between the cut surface and the worktop must be 90°.
The cut edges at the sides must be flat to ensure a good fit of
the retaining springs on the appliance. In laminated worktops, it
may be necessary to fit strips at the sides of the cut-out.
Remove shavings after cutting. Seal cut surfaces for resistance
to heat and so they are watertight.
Pay attention to a minimum gap of 10 mm from the underside of
the appliance to kitchen units.
Use suitable base constructions to ensure load-carrying
capacity and stability, especially in the case of thin worktops.
Pay attention to the weight of the appliance, including any
payload. Reinforcement material used must be resistant to heat
and moisture.
Note: Wait until the appliance has been installed in the
installation opening before checking that it is level.
Flush installation (Figure 1b)
Flush installation in a worktop is possible.
The appliance can be installed in the following temperature-
resistant and waterproof worktops:
Stone worktops
■
Worktops made of plastics (e.g. Corian
■
Solid wood worktops: Only by arrangement the with worktop
■
manufacturer (seal recess edges)
For other materials, coordinate with the worktop manufacturer
■
with regard to use.
Installation in laminated wood worktops is not possible.
Note: All recessing work on the worktop must be performed in a
specialist workshop on the basis of the installation sketch. The
recess must be produced neatly and precisely because the cut
edge is visible on the surface. Clean and degrease the recess
edges with a suitable cleaning agent (observe the silicone
manufacturer's processing notes).
Fitting several Vario appliances (Fig. 1c)
You can order the connecting strip VA 420 000/001/010/011
as a special accessory to combine several Vario appliances.
Allow for the additional space required for the connecting strip
when producing the cut-out (see installation instructions
VA 420 000/001/010/011).
)
®