Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Paint Crew
Daily maintenance
The only daily maintenance necessary is thorough cleaning.
Follow the cleaning procedures in this manual.
Extended maintenance
Some pump parts eventually wear out from use and must
be replaced. The following is a list of available repair kits.
TROUBLESHOOTING
PROBLEM
A. The sprayer does not start.
B. The sprayer starts but does
not draw in paint when
the PRIME/SPRAY knob is
set to PRIME.
C. The sprayer draws up
paint but the pressure
drops when the gun is
triggered.
D. The PRIME/SPRAY valve is
on SPRAY and there is flow
through the return tube.
E. The spray gun leaks.
F. The tip assembly leaks.
G. The spray gun will not
spray.
H. The paint pattern is tailing.
* Special repair kits with instructions are available for these procedures. Refer to the Parts List (page 32) section of this manual for a list of the
kits and their part numbers.
** Additional parts are available for this procedure. Refer to the Parts List (page 32) section of this manual for a list of the parts and their part
numbers.
WARNING
CAUSE
1)
The sprayer is not plugged in.
2)
The ON/OFF switch is set to OFF.
3)
The sprayer shuts off while still under
pressure.
4)
No voltage is coming from the wall plug.
5)
The extension cord is damaged or has too
low a capacity.
6)
There is a problem with the motor.
1)
The unit will not prime properly or has lost
prime.
2)
The hopper is empty.
3)
The unit is not on level ground.
4)
The inlet filter is clogged.
5)
The inlet or outlet valve is stuck.
6)
The inlet valve is worn or damaged.
7)
The PRIME/SPRAY valve is plugged.
1)
The spray tip is worn.
2)
The inlet filter is clogged.
3)
The gun or spray tip filter is plugged.
4)
The paint is too heavy or coarse.
5)
The outlet valve assembly is dirty or worn.
6)
The inlet valve assembly is damaged or
worn.
1)
The PRIME/SPRAY valve is dirty or worn.
1)
Internal parts of the gun are worn or dirty.
1)
The tip was assembled incorrectly.
2)
A seal is worn.
1)
The spray tip or the gun filter is plugged.
2)
The spray tip is in the CLEAN position.
3)
PRIME/SPRAY knob not set on SPRAY.
1)
The gun, the tip, or the inlet filter is
plugged.
2)
The tip is worn.
3)
The paint is too thick.
4)
Pressure loss.
MAINTENANCE
Pump performance is the only reliable indicator of when to
replace wear parts. Refer to the Troubleshooting section for
more information on when to use these kits.
Kit Part #
Description
0418912
Inlet and outlet valve kit
Before servicing, always release system pressure by
following PRESSURE RELIEF PROCEDURE (page 24).
SOLUTION
1)
Plug the sprayer in.
2)
Turn the ON/OFF switch to ON.
3)
Motor will cycle ON and OFF while spraying as it needs
pressure. This is normal. Resume painting.
4)
Properly test the power supply voltage.
5)
Replace the extension cord.
6)
Take sprayer to Wagner Authorized Service Center.
1)
Try to prime the unit again.
2)
Refill the hopper.
3)
Relocate unit to level ground.
4)
Clean the inlet filter.
5)
Clean the inlet and outlet valves and replace any worn parts.*
Inlet may be stuck from old paint. Push inlet filter tab to
release.
6)
Replace the inlet valve.*
7)
Take sprayer to Wagner Authorized Service Center.
1)
Replace the spray tip with a new tip.**
2)
Clean the inlet filter.
3)
Clean or replace the proper filter. Always keep extra filters
on hand.
4)
Thin or strain the paint.
5)
Clean or replace the outlet valve assembly.*
6)
Replace the inlet valve.*
1)
Take sprayer to Wagner Authorized Service Center.
1)
Take the sprayer to a Wagner Authorized Service Center.
1)
Check the tip assembly and assemble properly.
2)
Replace the seal.*
1)
Clean the spray tip or gun filter. Review
Spray Tip.
2)
Put the tip in the SPRAY position.
3)
Turn the PRIME/SPRAY knob to SPRAY.
1)
Clean the filters and strain the paint.
2)
Replace the spray tip.
3)
Thin the paint.
4)
Refer to Causes and Solutions for problem C.
GB
Unclogging the
31
Publicité
Table des Matières
Dépannage
