Technical Data; Before Starting The Equipment - EINHELL RG-SA 1433 Mode D'emploi D'origine

Anleitung_RG_SA_1433_SPK7:_
branch or hedge clippings. Moreover, the equipment
may not be used as a power cultivator to level out
high areas such as mole hills.
For safety reasons, the scarifier may not be used as
a drive unit for other equipment or toolkits of any
kind, unless specifically advised to do so by the
manufacturer.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Voltage:
Power consumption:
Working width:
Number of blades
Number of claws:
Scarifying depth:
L sound pressure level:
pA
L sound power level:
WA
Vibration on the shaft a
hv
K uncertainty
Protection class:
Protection type:
Weight

5. Before starting the equipment

The scarifier is delivered unassembled. The grass
basket and the complete push bar must be
assembled and mounted before using the scarifier.
Follow the operating instructions step-by-step and
use the pictures provided as a visual guide to easily
assemble the machine.
Fitting the push bar brackets (see Figs. 4 and 5)
Remove the star screw (Fig. 4/Item 1) and the
pressure plate (Fig. 4/Item 2)
09.09.2010 9:01 Uhr Seite 15
Connect the push bar bracket (Fig. 4/Item 3) to
the fastening screw. Ensure that the curve in the
tube (Fig. 5/Item 1) is facing outside.
Now remount the pressure plate and tighten with
the star screw. Important. The identical tilt angle
must be set for both push bar brackets.
Fitting the lower push bar (see Fig. 6)
Slide the lower push bar (Fig. 6/Item 1) over the
push bar brackets.
Do not forget to slide the stress-relief clip (Fig.
6/Item 2) onto the tube beforehand.
Now screw the tubes together using the screws
supplied (Fig. 6/Item 3), the plastic sleeves (Fig.
6/Item 4) and the star screw (Fig. 6/Item 5).
Fitting the upper push bar (see Fig. 7)
Position the upper push bar (Fig. 7) such that its
holes line up with the holes of the lower bar.
Now screw the tubes together using the screws
supplied (Fig. 7/Item 1), the plastic sleeves (Fig.
7/Item 2) and the star screw (Fig. 7/Item 3).
Using the cable clips supplied (Fig. 8), attach
the power cable to the tubes of the push bars so
that it is possible to open and shut the ejector
230 V ~ 50 Hz
flap (Fig. 9/Item A).
1400 W
Important!
Please ensure that the ejector flap can be
33 cm
opened and closed easily!
20 pieces
Assembling the grass basket
48
(see Figs. 10 and -13)
- 3 / 3 / 7 / 9 mm
Push both frame parts into each other (Fig. 10).
76.1 dB(A)
Pull the grass basket over the metal frame (Fig.
11).
99 dB(A)
Pull the rubber clips over the metal frame (Fig.
3.159 m/s 2
12).
1.5 m/s 2
To hang the grass basket on the scarifier you
must lift the ejector flap (Fig. 13/Item 1) with
II /
one hand and with the other hand take hold of
IPX4
the grass bag by the handle and hook it onto the
13 kg
scarifier from above (Fig. 13).
Important!
Before you ever hook the grass basket to the
scarifier you must ensure that the motor is switched
off and the cutting unit is not rotating.
Adjusting the handlebar height (see Fig. 17)
Loosen the star screw (Fig. 17/Item 1) on both
sides of the scarifier by turning several revolutions.
Now adjust the handlebar to the desired height.
Important!
The height of the handlebar may be adjusted within
the mark (Fig. 17/Item V) during operation.
GB
15