Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Tools and Parts
Tools Needed:
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools
listed here.
Measuring tape
■
Pencil
■
Masking tape or
■
thumbtacks
Scissors
■
No. 2 Phillips screwdriver
■
No. 3 Phillips screwdriver
■
for 1/4-20 x 3" bolts
Drill
■
3/16" (5 mm), 3/8" (10 mm),
■
5/8" (16 mm) drill bits
3/4" (19 mm) hole saw
■
Parts Supplied:
For information on reordering, see the "Replacement Parts"
section.
NOTE: The hardware items listed here are for wood studs.
For other types of wall structures, be sure to use
appropriate fasteners.
A
B
C
H
A. 3/16-24 x 3" round-head bolts (2)
B. 1/4-20 x 3" flat-head bolts (2)
C. Washers (2)
D. 3/16" toggle nuts (2)
E. 1/4" x 2" lag screws (2)
F. Sheet metal screws (2)
G. Power supply cord bushing (1)
H. Damper assembly (for wall
or roof venting)
NOTE: Depending on model, aluminum grease filter
and charcoal filter may be combined.
Materials needed:
Standard fittings for wall or roof venting. See
■
the "Venting Design Specifications" section.
INSTALLATION REQUIREMENTS
Diagonal wire cutting pliers
■
Stud finder
■
7/16" socket wrench
■
(or box wrench) for
1/4" x 2" lag screws
1
/
" (3.8 cm) diam.
1
■
2
hole drill bit for wood
or metal cabinet
Keyhole saw
■
Caulking gun and
■
weatherproof caulking
compound
Duct tape
■
D
E
F
G
Not Shown:
Upper cabinet template
Mounting plate (attached
to back of microwave oven)
Wall template
Aluminum grease filters
Charcoal filters (Depending
on model, charcoal filters
may not be included.
See User Instructions.)
Location Requirements
Check the opening where the microwave oven will be installed.
The location must provide:
Minimum installation dimensions. See the "Installation
■
Dimensions" illustration.
Minimum one 2" x 4" (50.8 mm x 101.6 mm) wood wall stud
■
and minimum 3/8" (10 mm) thickness drywall or plaster/lath
within cabinet opening.
Support for weight of 150 lbs (68 kg) which includes
■
microwave oven and items placed inside the microwave
oven and upper cabinet.
Grounded electrical outlet inside upper cabinet. See the
■
"Electrical Requirements" section.
NOTES:
If installing the microwave oven near a left sidewall, make
■
sure there is at least 6" (15.2 cm) of clearance between the
wall and the microwave oven, so that the door can open fully.
Some cabinet and building materials are not designed
■
to withstand the heat produced by the microwave oven
for cooking. Check with your builder or cabinet supplier
to make sure that the materials used will not discolor,
delaminate, or sustain other damages.
Special Requirements
For Wall Venting Installation Only:
Cutout must be free of any obstructions so that the vent
■
fits properly and the damper blade opens freely and fully.
For Roof Venting Installation Only:
If you are using a rectangular to round transition piece,
■
the 3" (7.6 cm) clearance needs to exist above the
microwave oven so that the damper blade can open
freely and fully. See "Rectangular to Round Transition"
illustration in the "Venting Design Specifications" section.
3
Publicité
Table des Matières
