Mounting And Changing The Brush/Drive Disks; Detergents - Instructions - Dustbane Hurricane Serie Manuel D'opération

Mounting and Changing The Brush/Drive Disks

IMPORTANT: Never work without the brushes, rollers and drive disks perfectly installed.
• Fitting the brush (one-brush models): Rest the brush on the floor in front of the machine and center it with the guard. Lower
the head and repeatedly action the brush/drive control lever (fig. 6, ref. 7) until the brush automatically engages on the flange
hub. If the manoeuvre is not successful, press on the handle again and repeat the centering and repeated actioning of the
brush/drive lever.
• Use of abrasive disks: fit the abrasive disk on the drive disk and perform the operations described for fitting the brush on the
scrubber drier.
• Removing the brush (one-brush models or no traction): Raise the machine head by pushing the head lift pedal down and
then to the right (fig. 6, ref. 9) and repeatedly action the brush/drive lever. After a few pulses, the brush/es (or drive disk) is
released and falls to the ground.
DANGER: These operations must be performed with the machine off.
• Fitting the brushes (two-brush models): Place the brushes under the head drive disk. Lift the right brush with your hands and
turn it clockwise, locking it in position on the drive disk. Lift the left brush with your hands and turn it anticlockwise, locking it
in position on the drive disk.
• Use of abrasive disks: fit the abrasive disk on the drive disk and perform the operations described for fitting the brush on the
scrubber drier.
• Removing the brushes (two-brush models): Raise the machine head by pushing the head lift pedal down and then to the
right (fig. 6, ref. 9). Turn the right brush anticlockwise, releasing it from the drive disk. Turn the left brush clockwise, releasing it
from the drive disk.
• Attaching the brush rollers: lift the head by pressing the head lowering/raising pedal (fig. 6, ref. 9) and fit the rollers in their
housing (fig. 16), first inserting them on the drive pulley and then pushing them upwards until they click into place.
• Removing the brush rollers: Head lowering/raising pedal (fig. 6, ref. 9): release the brushes by pulling them downwards from
the side opposite the drive pulley, then extracting them from their housing.
Fig. 16
Detergents – Instructions
Fig./Abb. 16
IMPORTANT: Always dilute the detergent according to the manufacturer's instructions. Do not use sodium hypochlorite (bleach) or other
фиг./реф. 16
oxidants, particularly in strong concentrations. Do not use solvents or hydrocarbons. The temperature of the water and detergent must not
exceed the maximum indicated in the technical specification. They must be free of sand and/or other impurities.
The machine has been designed for use with low-foam biodegradable detergents made specifically for scrubber driers. For a
complete and up-to-date list of the detergents and chemicals available, contact Dustbane. Use products suitable for the floor and
dirt to be removed only. Follow the safety regulations on use of detergents given in the section "Safety Regulations".
Preparing The Machine For Work
IMPORTANT: Before starting work, wear overalls, ear protectors, non-slip waterproof shoes, mask to protect the respiratory tract, gloves
and all other personal protection devices recommended by the supplier of the detergent used or necessitated by the work environment.
Before starting work, proceed as follows:
• Battery models: check the battery charge (recharge if necessary);
• Lower the head by means of the pedal (fig. 6, ref. 9);
• Make sure the dirty water drum (fig. 2, ref. 2) is empty. If necessary, empty it;
• R models with rollers: empty the debris bin (fig. 17).
Fig./Abb. 17
• Via the opening at the front, fill the detergent tank (fig. 2, ref. 7) with a suitable concentration of clean water and low-foam
фиг./реф. 17
detergent. Leave at least 5 cm between the surface of the liquid and the opening of the tank;
• Mount the most suitable brushes, drive disks or rollers for the floor and work to be performed (see paragraph 3.4);
12