Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
GENERAL SAFETY RULES-FOR ALL POWER TOOLS
WARNING!
READ ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in electric shock, fire
and/or serious injury. The term "power tool" in all of the warnings listed
below refers to your mains-operated (corded) power tool or battery-
opearted (cordless) power tool.
SAVE THESE INSTRUCTIONS
8.
WORK AREA SAFETY
1.
Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
2.
Do not operate power tools in ex-
plosive atmospheres, such as in
the presence of flammable liq-
uids, gases, or dust. Power tools
9.
create sparks which may ignite the
dust or fumes.
3.
Keep children and bystanders
away while operating a power
tool. Distractions can cause you to
lose control.
ELECTRICAL SAFETY
10. Use safety equipment. Always
4.
Power tool plugs must match the
outlet. Never modify the plug in
any way. Do not use any adapter
plugs with earthed (grounded)
power tools. Unmodified plugs and
matching outlets will reduce risk of
11. Avoid accidental starting. Ensure
electric shock.
5.
Avoid body contact with earthed
or grounded surfaces such as
pipes, radiators, ranges and re-
frigerators. There is an increased
risk of electric shock if your body is
12. Remove any adjusting key or
earthed or grounded.
6.
Do not expose power tools to rain
or wet conditions. Water entering a
power tool will increase the risk of
electric shock.
13. Do not overreach. Keep proper
7.
Do not abuse the cord. Never use
the cord for carrying, pulling, or
unplugging the power tool. Keep
cord away from heat, oil, sharp
edges, or moving parts. Damaged
or entangled cords increase the risk
of electric shock.
2
When operating a power tool out-
doors, use an extension cord suit-
able for outdoor use. Use of a cord
suitable for outdoor use reduces the
risk of electric shock.
PERSONAL SAFETY
Stay alert, watch what you are do-
ing and use common sense when
operating a power tool. Do not use
a power tool while you are tired
or under the influence of drugs,
alcohol or medication. A moment
of inattention while operating power
tools may result in serious personal
injury.
wear eye protection. Safety equip-
ment such as dust mask, non-skid
safety shoes, hard hat, or hearing pro-
tection used for appropriate conditions
will reduce personal injuries.
the switch is in the off-position
before plugging in. Carrying tools
with your finger on the switch or plug-
ging in power tools that have the
switch on invites accidents.
wrench before turning the power
tool on. A wrench or a key left at-
tached to a rotating part of the power
tool may result in personal injury.
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
14. Dress properly. Do not wear loose
22. Use the power tool, accessories
clothing or jewellery. Keep your
hair, clothing and gloves away
from moving parts. Loose clothes,
jewellery, or long hair can be caught in
moving parts.
15. If devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of these devices can reduce dust-
related hazards.
23. Have your power tool serviced by
POWER TOOL USE AND CARE
16. Do not force the power tool. Use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
17. Do not use the power tool if the
switch does not turn it on and off.
Any power tool that cannot be con-
trolled with the switch is dangerous
and must be repaired.
18. Disconnect the plug from the
power source and/or the battery
pack from the power tool before
making any adjustments, chang-
ing
accessories,
or
storing
power tools. Such preventive safety
measures reduce the risk of starting
the tool accidentally.
19. Store idle power tools out of the
reach of children and do not al-
low persons unfamiliar with the
power tools or these instructions
to operate power tools. Power
tools are dangerous in the hands of
untrained users.
20. Maintain power tools. Check for
misalignment or binding of mov-
ing parts, breakage of parts and
any other condition that may af-
fect the power tool's operation. If
damaged, have the power tool
repaired before use. Many acci-
dents are caused by poorly maintained
power tools.
21. Keep cutting tools sharp and
clean. Properly maintained cutting
tools with sharp cutting edges are less
likely to bind and are easier to control.
3
and tool bits etc., in accordance
with these instructions and in the
manner intended for the particu-
lar type of power tool, taking into
account the working conditions
and the work to be performed.
Use of the power tool for operations
different from those intended could re-
sult in a hazardous situation.
SERVICE
a qualified repair person using
only identical replacement parts.
This will ensure that the safety of the
power tool is maintained.
Publicité
Table des Matières
