Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
23. OPERATION (
CONT
• E
L
P
RASE
INK
ROCESS
1. A
L
CTIVATE THE
INK MODE OF THE HOOD
Simultaneously press the Master Link Mode and Auto Link Mode push buttons (push buttons 3 and 4 on control illustration) for
2 seconds; all 4 speed level LEDs flash.
2. E
L
RASE ALL LINKED
INK
Press the Erase Link push button (push button 1 on control illustration) for 2 seconds to start the Erase-link process, all 4 speed level
LEDs flash in rotation on the power pack interface until links are erased.
NOTE: For some LinkLogic
3. E
L
XIT
INK MODE OF THE HOOD
Press and hold the Exit Link mode push button (push button 2 on control illustration) for 2 seconds to exit Link mode. Link mode
remains activated for 4 minutes if no other operation is done.
24. LINKLOGIC SYSTEM CONTROL BOARD JUMPERS
The LinkLogic system is designed to work with devices like the Broan SmartSense™ Fan system that requires CFM output for this range
hood. If you are using this power pack with a LinkLogic device that requires CFM information, please follow the simple instruction/matrix
below to configure the LinkLogic control board in the power pack to provide the correct CFM information. To access the LinkLogic control
board, remove baffle filters. Remove screws retaining the control panel to the hood. Rotate carefully the control panel in order to see the
LinkLogic board jumpers. Remove jumpers from current location on pins and reconfigure based on blower performance.
3
2
1
HE0089
L
L
INK
OGIC BOARD JUMPERS
If you are unsure if the LinkLogic accessory or device requires CFM data, please refer to the unit instructions.
NOTE: If during normal operation, all 4 speed level LEDs quickly flash twice and in rotation, an error occurred while communicating with
a linked LinkLogic device. Reset this error flag by entering and then exit the Linking mode.
25. WARRANTY
Broan-NuTone LLC ("Broan-NuTone") warrants to the original consumer purchaser of its products that such products will be free
from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be
defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES AND BULBS, FUSES, FILTERS, DUCTS,
ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and
service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other
than by Broan-NuTone), faulty installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states or provinces
do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
BROAN-NUTONE'S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE'S OPTION, SHALL BE THE PURCHASER'S
SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE.
Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to another.
Any modification performed on this product without the authorization of Broan-NuTone will void this warranty. This warranty supersedes
all prior warranties.
To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number stated below, (b) give the model
number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service,
you must present evidence of the original purchase date.
'
)
D
L
OGIC DEVICES
®
devices, LEDs might not flash because the linking duration is too short.
P
1
P
2
P
IN
IN
0
0
0
0
0
1
0
1
0 = N
O JUMPER ON PIN
ONE-YEAR LIMITED WARRANTY
Best
®
, 926 W. State Street, Hartford, WI 53027 (1-800-558-1711)
®
Best
, 550 Lemire Blvd., Drummondville, QC, Canada (1-866-737-7770)
www.bestrangehoods.com
3
M
CFM
IN
AXIMUM
VALUE
0
0 CFM
1
300 CFM
0
500 CFM
1
600 CFM
1 = J
UMPER ON PIN
17
P
1
P
2
P
3
M
IN
IN
IN
AXIMUM
1
0
0
1
0
1
1
1
0
1
1
1
0 = N
O JUMPER ON PIN
CFM
VALUE
900 CFM
1000 CFM
1200 CFM
1500 CFM
1 = J
UMPER ON PIN
Publicité
Table des Matières
