Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
•
Make sure the power sockets used for battery charger are connected to a suitable earth system and protected by
differential thermal solenoid switches.
•
It is indispensable to respect the battery manufacturer's instructions and current legislation. The batteries should
always be kept clean and dry to avoid surface leakage current. Protect the batteries from impurities such as metal dust.
NeveR rest tools on the batteries as this could cause short circuit and explosion.
•
•
When using battery acid, always follow the relative safety instructions scrupulously.
•
To recharge the batteries, always use the battery charger supplied with the machine (when provided).
•
In the presence of particularly strong magnetic fields, assess the possible effect on the control electronics.
•
NeveR wash the machine with water jets.
•
The fluids collected during operation contain detergent, disinfectant, water, organic and inorganic material. They must
be disposed of in accordance with current legislation.
•
In the case of malfunction and/or faulty operation, turn the machine off immediately (disconnecting it from the
batteries) and do not tamper. Contact a service centre authorised by Dustbane.
•
All maintenance operations must be performed in an adequately lit place and only after disconnecting the machine
from the power supply (in battery models by disconnecting the batteries).
•
All work on the electrical system and all maintenance and repair operations (particularly those not explicitly described
in this manual) must be performed by specialised personnel expert in the sector only.
•
If the power cable, plug or terminals require replacing, make sure the electrical connections and cable grip are
tightly fastened to guarantee the resistance of the cable if pulled. Only original accessories and spare parts supplied
by the Manufacturer may be used in order to guarantee safe problem-free operation of the machine. Never use parts
removed from other machines or from other kits.
Handling And Installation
During all lifting operations, make sure the packaged machine is firmly anchored to avoid it tipping up or being
accidentally dropped. Always load/unload lorries in adequately lit areas.
Lifting And Transporting The Packaged Machine
The machine, packaged on a wooden pallet by the Manufacturer, must be loaded using suitable equipment and subsequent
amendments and/or additions) onto the transporting vehicle. At destination, it must be unloaded using similar means.
The squeegees are packed in cardboard boxes without pallet. A fork lift truck must always be used to lift the packaged body of the
machine. Handle with care to avoid knocking or overturning the machine.
Checks On Delivery
When the carrier delivers the machine, make sure the packaging and machine are both whole and undamaged. If the machine is
damaged, make sure the carrier is aware of the damage and before accepting the goods, reserve the right (in writing) to request
compensation for the damage.
Power Supply Batteries
AGM battery may be installed on these machines. In AGM batteries, the electrolyte level must be checked regularly. When necessary,
top up with distilled water until the plates are covered. Do not overfill (5 mm max. above the plates).
The technical characteristics must correspond to those indicated in the paragraph on the technical specification of the machine.
The use of heavier batteries could seriously jeopardise manoeuvrability and lead to the brush motor overheating. Batteries with a
lower capacity and weight will require recharging more frequently. They must be kept charged, dry and clean and the connections
must be tight.
Batteries: Preparation
DANGER: While installing or performing maintenance on the batteries, the operator must be provided with the necessary personal
protection devices (gloves, goggles, overalls, etc) to limit the risk of accident. Keep away from naked flames, avoid short circuiting the
battery poles, avoid sparks and do not smoke.
The batteries are normally supplied filled with acid and ready for use. If the batteries are dry, before mounting them on the machine,
proceed as follows:
•
Remove the caps and fill all elements with specific sulphuric acid solution until the plates are entirely covered (this requires at
least a couple of passes for each element);
•
Leave for 4-5 hours to allow the air bubbles to come to the surface and the plates to absorb the electrolyte;
•
Make sure the level of electrolyte is still above the plates and if necessary top up with sulphuric acid solution;
5
Publicité
Table des Matières
