Safety Information - EdilKamin PELLET-BLOK Installation, Usage Et Maintenance

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 40
PRINCIPIO DI FUNZIONAMENTO
PELLET-BLOK is a stove that uses wood pellets as fuel,
whose combustion is controlled electronically.
The fuel (pellets) is taken from the storage tank (A) and, via
an Archimedes' screw (B) activated by a gear motor (C), is
transported into a second Archimedes' screw (D) activated
by a second gear motor (E) it is then transported to the com-
bustion crucible (F).
The pellets are ignited by the air that is heated by an elec-
trical resistance (G) and drawn into the combustion cham-
ber by a smoke extractor (H).
The smoke produced by the combustion, is extracted from
the hearth via the same fan, and expelled by the outlet (I)
located on the upper part of the fireplace.
The fireplace channels the hot air and conveys it in order to
heat adjacent rooms. There are two Ø14 cm outlets on the
fireplace's lid for connecting special aluminium pipes. An
Optional KIT 3 is available in order to channel the warm air
(see page 29).
The hearth is made of Ecokeram
and frontal closure via a small door.
The door is opened and closed using the "cold handle" sup-
plied.
Fuel quantity, smoke extraction and combustion air supply
are all controlled by an electronic control board, which is
equipped with LEONARDO
combustion efficiency and low emissions.
Complete combustion that reduces to a minimum the pro-
duction of ash and results in increased autonomy, as well as
low emissions, is also guaranteed by the 3C SYSTEM devi-
ce (ceramic catalytic combustor).
F
H
fig. 1
with cast iron hearth base
®
software to achieve high
®
I
A
B
D
C
E
G

SAFETY INFORMATION

PELLET-BLOK is designed to heat through automatic
pellet combustion in the hearth. It heats the room where it
is installed by radiation and by circulating the air coming
out of the upper front grille, and it heats the two adjacent
rooms by circulating the hot air channelled by the outlets
located on the lid.
• The only risks that may derive from using the fireplace
pertain to non-compliance with installation instructions,
direct contact with live electrical parts (internal), contact
with the fire or hot parts (glass, pipes, hot air output), or
foreign substances being put in the fireplace.
• Only use wood pellets with 6 mm diameter as fuel.
• Should components fail, the fireplace is equipped with
safety devices that guarantee automatic shutdown. These
are activated without any intervention required.
• In order to function correctly, the fireplace must be
installed in accordance with the instructions given herein
and the door must not be opened during operation: com-
bustion is fully automatic and requires no intervention.
• Under no circumstances should any foreign substances
be entered into the hearth or hopper.
• Do not use flammable products to clean the smoke
channel (the flue section connecting the fireplace smoke
outlet to the chimney flue).
• Hearth and hopper components must only be cleaned
with a vacuum cleaner.
• The glass can be cleaned when COLD with a suitable
product (e.g. GlassKamin Edilkamin) and a cloth.
• Ensure that the fireplace is installed and ignited by a
qualified Edilkamin DEALER, in accordance with the
instructions given herein.
• When the fireplace is in operation, the exhaust pipes
and door become very hot (do not touch without wearing
the thermal glove).
• Do not place anything, which is not heat resistant near
the fireplace.
• NEVER use liquid fuel to ignite the fireplace or rekin-
dle the embers.
• Do not block the fireplace's external air intake.
• Do not wet the fireplace and do not go near electrical
parts with wet hands.
• Do not use reducers on the smoke exhaust pipes.
• The fireplace must be installed in a room that is suita-
ble for fire prevention and equipped with all that is requi-
red (power and air supply and outlets) for the stove to
function correctly and safely.
• Should ignition fail, DO NOT re-ignite until you
have emptied the combustion chamber.
•ATTENTION: THE PELLET EMPTIED FROM
THE COMBUSTION CHAMBER MUST NOT BE
DEPOSITED INSIDE THE HOPPER.
22

Publicité

Table des Matières
loading

Table des Matières