Scope Of Delivery; Intended Use - Scheppach MNF1400 Traduction Des Instructions D'origine

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 20
Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment and
success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability for
damages to the product or damages caused by the prod-
uct that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due
to the non-compliance of the electric regulations and
VDE regulations 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating instruc-
tions before installing and commissioning the device. The
operating instructions are intended to help the user to
become familiar with the machine and take advantage of
its application possibilities in accordance with the recom-
mendations. The operating instructions contain impor-
tant information on how to operate the machine safely,
professionally and economically, how to avoid danger,
costly repairs, reduce downtimes and how to increase
reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in your
country. Keep the operating instructions package with
the machine at all times and store it in a plastic cover
to protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information. The machine can only be
operated by persons who were instructed concerning the
operation of the machine and who are informed about
the associated dangers. The minimum age requirement
must be complied with.
14
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Layout (Fig. 1)
1.
ON/OFF switch
2.
Handle
3.
Dust extraction adapter
3a.
Union nut
4.
Blade guard
5.
Locking flange (with thread)
6.
Locking screw for the depth stop
7.
Depth stop
8.
Additional handle
9.
Safety lock-out
10.
Spindle lock
11.
Roller
12.
Reducer
13.
Flange
14.
Blotters
15.
Face spanner
16.
Hand chisel
17.
Backing flange

Scope of delivery

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the pack-
aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
1 wall chaser
1 face spanner
1 reducer
1 hand chisel

Intended use

The wall grinder (standard nomenclature: abrasive
cutting appliance), hereinafter referred to as the appli-
ance, is designed for making cuts or slits (without the
use of water) in firmly supported and primarily min-
eral materials such as concrete or masonry, using the
guide carriage and in combination with an approved
industrial dust extractor. Any other usage of or modifi-
cation to the appliance is deemed to be improper and
carries the risk of serious personal injury. Not for com-
mercial use.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

5802601901

Table des Matières