Settings Menu - AEG KRC 4368 DAB+ Mode D'emploi

English
44 44
played. If information on the track title is transmitted
by the station, you can display this information with the
INFO / MENU button.
• Displays the received signal strength.
• This indicates the station category (e.g. Pop-Music, News
etc.).
• Displays the name of the station group (e.g. DR
Deutschland).
• Frequency of the current radio station.
• The "SIGNAL ERROR" display shows the signal quality.
The lower the adjacent fi gure, the better the quality.
• Displays the digital Audio Bit Rate.
• Display the time.
• Display the date.
Save station
1. If you have found the desired station, hold down the
PRESET button (11). The fi rst preset location appears on
the display. If the preset location is still empty the word
EMPTY appears under PRESET STORE.
2. For choosing the memory position, please press SKIP + /
SKIP – buttons (5 / 6).
3. Press SCAN / SELECT to save the settings.
Select a preset station
1. Press the PRESET button (11).
2. Press the SKIP + / SKIP – buttons (5 / 6) to choose a memory
position.
3. Confi rm your selection with the SCAN / SELECT button
(4).

Settings menu

Numerous settings are made via the Settings menu (see
page 5).
In the Settings menu you can fi nd the main menu and the
related submenus with the individual options.
To open the menu, keep the INFO / MENU button (12)
pressed during operation
• Use the SKIP + / SKIP – buttons (5 / 6) to navigate in the
menu.
• Use the SCAN / SELECT button (4) to select a submenu,
or confi rm a setting.
• To exit the menu, press the INFO / MENU button (12).
NOTE:
• If you do not press any button within 30 seconds, the
menu is hidden.
• The currently set option is highlighted by " ".
A Settings menu can be found in DAB mode, as well as in
FM mode. The DAB and FM menu is explained below along
with the general SYSTEM menu.
DAB Menu
The DAB menu is divided into menus: Full scan, Manual
tune, DRC and Prune.
KRC4368DAB+_IM
• Full scan: Starts the station scan. The DAB frequency
band is scanned for stations.
• Manual tune: To do so you need to know the station
frequency. This can be found on the internet site of the
broadcasting service. Select individual frequencies using
the SKIP + / SKIP – buttons (5 / 6).
• DRC: short for Digital Range Control (dynamic range).
The term DRC describes the ratio between the quietest
and the loudest sound. If the dynamic range is very high
there are very soft sounds as well as very loud sounds.
Under some circumstances this may present a problem
with playback. Let us assume that you are listening to a
radio station in a relatively loud environment. By increas-
ing the volume you can play the quiet sections louder.
This however has the disadvantage that the loud sections
become uncomfortably loud. It makes sense here to
reduce the dynamic range. Select between the options:
- DRC off: The dynamic range is not reduced.
- DRC high: The dynamic range is sharply reduced.
- DRC low: The dynamic range is slightly reduced.
• Prune: It may be that you can no longer receive some sta-
tions after a station scan or change of location. With this
function you can delete these stations from the reception
list. Select "YES" and confi rm with the SCAN / SELECT
button.
FM Menu
• Scan setting: Select the desired option for automatic
station search.
- Strong stations only: Only clear stations are searched.
- All stations: Search for all stations that can be received.
In this case, station search also stops for weak stations.
DAB + FM Menu (SYSTEM)
The following submenus can be found in the SYSTEM menu.
• Egg timer: Refer to the chapter "Short-time Timer" on
page 45.
• Time: Set the time and the date manually. You can also
set the automatic update and the display format of the
date.
- Set Time/Date: Here, you can manually set the time
and date.
- Auto update: Here, select the source from which the
automatic update of time and date should be carried
out. Select from: Update from all sources, DAB only,
FM only and no update.
- Set 12/24 hour: Select between 24 hour and 12 hour
display.
NOTE: In 12 hour display
AM = morning, PM = afternoon appears.
- Set date format: Select between the two options
for displaying the date. Day – Month – Year or Month –
Day – Year.
17.12.15