Before Starting The Machine; Operation; Technical Data; Maintenance - EINHELL BMH 33/36 Mode D'emploi

Anleitung BMH 33-36 SPK1
GB
9. Feed the clutch cable through the holder for the
steering handles and fasten the Bowden wire
adjuster to the eyelet provided on the steering
handle by unscrewing the upper lock nut and
inserting the thread on the adjuster through the
eyelet. Then attach the Bowden wire to the
clutch lever.
10. Fit the clutch lever to the left-hand steering
handle and fasten the clutch lever to the stee-
ring handle with the screw (21) and the wing nut
(22) (see Fig.18).
1. Adjust to the right length with the help of the
adjuster (see Fig. 17/A) as follows: When the
clutch lever is pressed there must be sufficient
tension in the V-belt for the star-type hoes to
turn, whereas when the clutch lever is released
the star-type hoes must not move. Then tighten
the two nuts against each other.
12. To fit the throttle lever, first unscrew the screws
on the throttle lever. Then attach the throttle
lever to the right-hand steering handle (5) (Fig.
19).

6. Before starting the machine

Important! You must fill up with engine oil (approx.
0.6 l) and fuel before you can start the engine.
Check the fuel and engine oil levels and refill or
top up if required.
Make sure that the ignition cable is secured to
the spark plug.
Check the area immediately around the power
cultivator.

7. Operation

Set the depth stop (4) to the desired depth and
secure with the split pin.
Swing the transport wheel up and make sure
that the bolt is engaged in the notch in the
mount at the front.
Push the petrol choke (Fig. 1/Item A) to the
"ON" position.
Push the starter lever down to the "Choke" posi-
tion (Fig. 19/Item A).
Pull the start cable gently until you feel resi-
stance, then pull vigorously. If the engine does
not start up immediately, repeat the above
steps.
Move the starter lever to the position in the
middle (Fig. 19/Item B) = working position
(Engine speed: fast/slow).
Starter lever position (Fig. 19/Item C) = stop
engine.
Depending on how tall you are you can adjust
the complete holder for the steering handles to
the top position. To do so, unscrew the
screws(Fig. 14/Item A), adjust the bracket and
14
10.08.2006 9:31 Uhr Seite 14
retighten the screws.
To start the star-type hoes, press the clutch
handle (8) down and hold in this position.
Releasing the clutch handle brings the star-type
hoes to a stop (if they do not stop, readjust the
clutch cable).

8. Technical data

Engine: 4-stroke engine, 163 ccm
Engine rating:
Engine working speed:
Working width:
Hoe blade diameter:
Forward gear:
Starting system:
Fuel: Regular unleaded petrol
Engine oil: approx. 0.6 l (10W30)
Tank capacity:
Vibration ahv:
Weight:
Spark plug:

9. Maintenance

Remove dust and dirt regularly from the machi-
ne. Cleaning is best carried out with a fine brush
or a cloth.
Never use caustic agents to clean plastic parts.
Take the petrol out of the power cultivator if you
do not intend to use the cultivator for a lengthy
period of time.
Please note: Switch off the unit immediately and
contact an authorized dealer:
In the event of unusual vibrations or noise.
If the engine appears to be overloaded or misfi-
res.

9.1 Air filter maintenance

Check and clean the air filter before every use,
and replace it if necessary.
Undo the screw on the air filter cover (Fig. 20)
and remove the cover (Fig. 21).
Remove the filter element (Fig. 22).
Do not use abrasive cleaning agents or petrol to
clean the element.
Clean the element by tapping it on a flat surfa-
ce.
Assemble in reverse order.
3.3 kW / 4.5 hp
3200 rpm
36 cm
26 cm
1
Reversing starter
approx. 2.3 l
6.1 m/s 2
34 kg
F7 TC