Technical Data; Before Starting The Equipment - EINHELL GE-CR 30 Li Traduction Du Mode D'emploi D'origine

The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.

4. Technical data

Motor power supply: ............. 36 V
No Load Speed: .......................... 140 rpm (min
Cultivating width max: ..............11.8 in. (300 mm)
Cultivating depth max:.................7.9 in. (200 mm)
Tines: ...............................4 steel cultivating tines
Weight: ....................................... 26 lbs (11.8 kg)
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
Anl_GE_CR_30_Li_USA_SPK7.indb 12 Anl_GE_CR_30_Li_USA_SPK7.indb 12
EN

5. Before starting the equipment

Warning!
Always pull out the safety plug before making
adjustments or carrying out maintenance,
cleaning and repair work on the equipment.
Assembly (Fig. 3-9)
•
Pull out the split pin (Fig. 3/Item 13) and
remove the pin (Fig. 3/Item 14). Push the
brake shoe (Fig. 4/Item 12) into the mount
and fix it in position with the pin and split pin
previously removed.
•
Undo and the Philips screws (Fig. 4/Item
15) with washers on both sides of the axle.
On both sides, push the transport wheel as
(2x 18V)
shown in Fig. 5 onto the axle and secure with
)
-1
the Philips screws (15) and washers (Fig. 5/
Item 16) on each side.
•
Press the wheel caps (Fig. 6/Item 11) onto
the transport wheels.
•
Push the lower push bar onto the motor unit
(Fig. 7/Item 3) as shown in Fig. 7 and fasten
it with the screws (Fig. 7/Item 9) and the star
nuts (Fig. 7/Item 8).
•
Push the upper push bar (Fig. 8/Item 1) onto
the lower push bar (Fig. 8/Item 2) and fasten
it with the screws (Fig. 8/Item 9) and the star
nuts (Fig. 8/Item 8).
•
Secure the cable to the push bars with two
cable securing clips (Fig. 9/Item 7).
Installing the battery (Fig. 10-11)
Open the battery cover. This is done by pressing
the lock release (21) as shown in Fig. 10 and
swinging up the cover. Then slot the two batteries
into the mounts as shown in Fig. 11 and push
them forward until you hear the batteries engage.
Important!
Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment's operating time depends on
the battery with the lower charge level. The two
batteries must always be fully charged before use.
Close the battery cover by swinging it down, and
make sure that it latches in place correctly.
- 12 -
24.06.2019 11:08:29 24.06.2019 11:08:29