General Safety Instructions; Machine Layout And Items Supplied; Intended Use; Environmental Protection - EINHELL BMH 33/36 Mode D'emploi

Anleitung BMH 33-36 SPK1
Packaging:
The unit is supplied in packaging to prevent it from
being damaged in transit. This packaging is raw
material and can therefore be reused or can be
returned to the raw material system.
When using the equipment, a few safety precau-
tions must be observed to avoid injuries and
damage.
Read the operating instructions carefully and
comply with them. It is important to consult
these instructions in order to acquaint yourself
with the unit, its proper use and safety regulati-
ons.
Keep this manual in a safe place, so that the
information is available at all times.
If you give the equipment to any other person,
give them these operating instructions as well.
We cannot accept any liability for damage or
accidents which arise due to a failure to follow
these instructions.

1. General safety instructions

The general safety instructions and explanations of
the information signs on the unit are set out in the
enclosed booklet.

2. Machine layout and items supplied

(Fig. 1-3)
1 Holder for steering handle
2 Transport wheel with holder
3 Engine / gear unit
4 Depth stop
5 Steering handle – throttle lever
6 Steering handle – clutch handle
7 Reversing starter
8 Clutch handle
9 Bolts for spark plug wrench
10 Spark plug wrench
11 Safety split pin for depth stop
12 Resetting spring for transport wheel
13 Four screws size M6 x 30 for fastening the
steering handle
14 Four screws size M6 x 20 for the steering
handle holder
15 Four nuts size M6
16 Four washers with size 6 diameters
17 Four circlips with size 6 diameters
18 Four washers with size 6 diameters
19 Screw size M8 x 80
10.08.2006 9:31 Uhr Seite 13
20 Nut size M8
21 Screw size M6 x 35
22 Wing nut size M6
23 Safety split pin for resetting spring
24 Open-ended spanner size 10/12
25 Open-ended spanner size 13/15

3. Intended use

The machine is designed for digging over beds and
fields. Be sure to observe the restrictions in the
additional safety instructions.

4. Environmental protection

Dispose of soiled maintenance material and
operating materials at the appropriate collection
point.
Recycle packaging material, metal and plastics.
5. Assembly (Fig. 4-20)
1. Place the engine/gear unit on its left side and
then assemble the power cultivator as follows.
2. Insert the transport wheel holder in the mount
on the drive unit (see Fig. 4).
3. Fasten the transport wheel holder with the help
of the screw (19) and the nut (20) (see Fig. 5
and 6).
4. Tension the resetting spring between the engine
unit and the transport wheel holder (2). To do
so, first hang the hook on the spring in the hole
on the inside of the gear unit in the hole provi-
ded. Then fit the eyelet on the spring onto the
bolt notches on the transport wheel. Now insert
the safety split pin (23) in the bolt hole provided
on the transport wheel to secure the spring and
ensure that it cannot slip off (Fig. 7-8).
5. Insert the depth stop in the opening at the back
of the gear unit and fasten it with the safety split
pin (11) at the working height you require (3
positions are available; when using for the first
time we would recommend the middle position)
(Fig. 9-10).
6. Stand the power cultivator upright and feed the
Bowden wire for the clutch through the lower
opening in the holder for the steering handles
(Fig. 11).
7. Fit the holder for the steering handles to the
engine unit and fasten with the screws (14), the
circlip (17) and the washers (16) as shown in
Fig. 12-14.
8. Then fit the steering handles through the ope-
nings on the holder for the steering handles and
fasten with the screws (13), washers (18) and
nuts (15) as shown in Fig. 15-16 .
GB
13