EINHELL BT-PS 800 Mode D'emploi D'origine page 15

Anleitung_BT_PS_800_SPK7.qxd__ 19.12.14 08:47 Seite 15
(Fig. 1/Item 3) flashes.
3. It takes around 18 hours to charge the energy
station.
Pressing the pushbutton (Fig. 1/Item 4) displays the
charge state of the built-in battery on the integrated
voltage meter (Fig. 1/Item 5).
5.2 Charging the energy station with the 12 V
adapter cable (Fig. 1/Item 13)
The energy station can be charged through the
vehicle's 12V cigarette lighter.
Charging should be performed only while driving, as
the vehicle's battery is discharged in the process.
Never start the vehicle while the 12V adapter cable is
connected to the cigarette lighter.
Insert the 12V plug of the 12V adapter cable into the
vehicle's cigarette lighter and insert the other end of
the cable into the charging jack of the energy station
marked "Recharge".
6. Outputs
Caution!
Risk of short-circuiting! Ensure the correct polarity of
the consumer you want to connect up (positive pole
on the inside). Refer to the instructions in the
operating manual for your consumer equipment.
Output 12 V cigarette lighter socket. max 10 A.
¼
The 12 V output (Figure 1 / Item 8) can be
loaded with max. 10 A, i.e. you have max. 10 A
at your disposal.
¼
Check the power and power consumption values
of the consumer to ensure that you do not
overload the energy station. If you only know the
power data of the consumer you can calculate
the max. current very easily.
Example:
Consumer: 12 V / 50 W
The current consumption is 50 W / 12 V
= 4.17 A
¼
The supplied 12 V adapter cable can be used to
connect a suitable consumer.
¼
Remove the caps to use the 12 V output and
connect the consumer.
Check that the voltage and current ratings of the
consumer units will not overload the energy
station.
Overloading may destroy the energy station.
7. To operate the lamp
Proceed as follows to switch on the lamp:
The lamp (Figure 1 / Item 6) is switched on and off
using the switch (Figure 1 / Item 7).
8. Starting aid for motor vehicles
Danger!
¼
The charging cable with the pole clamps is
located on the side of the unit.
¼
When the jumper cables are not in use, do not
remove them from the energy station.
¼
Caution! Risk of short-circuiting if the pole
clamps touch each other.
¼
Use the energy station as a source of starting aid
only when the vehicle battery is partially
discharged. The energy station is designed
provide the car battery with only a limited charge.
¼
The energy station is not suitable for starting
a vehicle with a fully discharged battery.
The energy station's starting aid function provides
welcome help when a vehicle's battery lacks
sufficient charge to start the vehicle without difficulty.
We wish to point out that even standard vehicle
models are equipped with numerous electric
modules (e.g. ABS, ASC, fuel injection pump, on-
board computer and car phone). The higher starting
voltage and voltage peaks may cause damage to
electronic components. No product liability can be
accepted for any damage resulting from the energy
station's starting aid function. Please read the
information in the operating manuals of your vehicle,
radio, car phone, etc.
Important. Jump starting is possible only when
the energy station is charged to full capacity.
How to use the energy station to start a vehicle
(fig. 1)
1. Connect the red cable (+) of the energy station to
the POSITIVE pole (+) of the vehicle battery.
2. Connect the black cable (-) of the energy station
to the vehicle's earthing strip or any other bare
point on the engine block (earth). Choose a point
as far away as possible from the battery in order
to prevent ignition of any explosive electrolytic
gas which may develop.
3. Turn the ignition key over to start position and
wait approx. 2 minutes.
DO NOT START THE ENGINE!
4. With the energy station connected, you can now
GB
15