Descaling - Unold 28811 Notice D'utilisation

(STANDBy AFTER 120 MIN.), the appliance switches to standby
mode 120 minutes after the last operation carried out.
When the display indicates
STANDBy
NACH 240 MIN
(STANDBy AFTER 240 MIN.), the appliance switches to standby
mode 240 minutes after the last operation carried out.
When the display indicates
STANDBy
NACH 480 MIN
(STANDBy AFTER 480 MIN.), the appliance switches to standby
mode 480 minutes after the last operation carried out.
The default setting is staNDBY.
To confirm the setting immediately, press the MeNÜ/MENU button
for three seconds, thus abandoning the menu.
To programme further changes, press the MeNÜ/MENU button
once briefly, in order to access the next option.
cup totalisator
The cup totalisator indicates the total number of cups of coffee
prepared since the starting up of the appliance.
To activate the menu, press the MeNÜ/MENU button until the
message on the display changes.
Press the MeNÜ/MENU button six times. The following message
is displayed:
GESAMTANZAHL
00000
This submenu does not allow any settings. Please bear in mind
that due to the in-plant tests a certain number of cups will be
indicated.
This feature deletes all personal settings and re-establishes the
default settings.
To activate the menu, press the MeNÜ/MENU button until the
message on the display changes.
Press the MeNÜ/MENU button seven times. The following message
will be displayed:
WERKSEINSTELLUNG
Press the MeNÜ/MENU button and maintain it pressed for 3
seconds. After this the appliance has re-established the default
settings.
automatic descaling
To activate the menu, press the MeNÜ/MENU button until the
message on the display changes.
Press the MeNÜ/MENU button eight times. The display
indicates:

Descaling

Our automatic coffee machines have a descaling memory and an automatic descaling programme and also offer the possibility for
manual descaling.
If the flow rate decreases or coffee is no longer brewed, a manual descaling is recommended.
Use an ecological descaling product. Make sure that the descaling product is adequate for automatic coffee machines.
MaNUal DescalING
If the flow rate decreases or coffee is no longer brewed, a manual
descaling is recommended.
Fill the water tank with the descaling product.
Switch the appliance on and wait until „Betriebsbereit/Ready" is
indicated.
Now press the button „Coffee mug".
28
Reset
ENTKALKEN
NICHT STARTEN
The automatic descaling will not start. After reaching the number
of cups set in the water hardness settings, the following message
is indicated:
GERäT
ENTKALKEN
Press the button once.
The following message will be displayed:
ENTKALKEN
STARTEN
After abandoning the menu, the automatic descaling process
starts.
If you access the submenu for the settings of the water hardness
by pressing the MeNÜ/MENU button, all previous settings will not
be saved!
closing the programming mode
save changes
If you maintain the MeNÜ/MENU button pressed until the
displayed indication shifts, all previous programme changes will
be saved.
This may be carried out for each item of the menu individually.
Nevertheless, you may also use the MeNÜ/MENU button and the
buttons
and to browse all submenus, carry out the desired
settings and confirm and save these settings altogether at the
end.
closing the programming mode without saving
If no button is pressed during approx. 5 seconds when being in
programme mode, the programme mode is abandoned without
saving the changes made.
If you access the submenu for the settings of the water hardness
by pressing the MeNÜ/MENU button, all previous settings will not
be saved! If this happens accidentally, you will have to repeat all
changes previously made and not saved.
With resistant calcinations it might be necessary to press the
button several times until the normal flow rate is achieved.
As soon as the flow rate is normal again, press the button „Coffee
mug" twice.
After this empty and clean the water tank.
Fill the water tank with fresh, cold water and insert the tank into
the appliance.