Safety Information - Invacare H335 Manuel D'utilisation

R7766 – Armpad (Fig. 5)
Pos. Designation
Armpad, PUR
A
Glue
B
R7767 – Aesthetic cover (Fig. 6)
Pos. Designation
Plastic cover
B
Screw and nut
C
Protective cap
D
Warranty
We provide a manufacturer's warranty for the product
in accordance with our General Terms and Conditions of
Business in the respective countries. Warranty claims can
only be made through the provider from whom the appliance
was obtained.
Compliance
Quality is of the utmost importance for our company; all
processes are based on the ISO 13485 standard.
This product features the CE mark, in compliance with the
Medical Device Directive 93/42/EEC Class 1.
Invacare is continuously working towards ensuring that the
company's impact on the environment, locally and globally,
is reduced to a minimum. We only use REACH compliant
materials and components.
For further information please contact Invacare in your
country (for addresses, see back page of this manual).
Service life
The expected service life of this product is five years
when used daily in accordance with safety instructions and
intended use, stated in this manual. The effective service life
can vary according to frequency and intensity of use.
Safety

Safety information

WARNING!
Risk of falling!
– Do not use if defective.
– Do not use as sports equipment.
– Do not use as a climbing aid.
Labels and symbols on the product
Identification label (Fig. 8)
Manufacturer address
A
Conformity mark
B
Lot number
C
Maximum user weight
D
Read user manual
E
Date of manufacture
F
Product designation
G
1572997-D
Setup and usage
Quantity
1
Installing the support folding handle
1
Quantity
1
Defining the installation height (Fig. 1)
1
1. With the user standing upright, without shoes, measure
2
Installing the support bar (H335 / R7762) (Fig. 1)
1. Insert the 2° adjustment plate D.
2. Mark out the location of the holes on the wall (2 above
3. Remove the 2° adjustment plate.
4. Position the wall attachment socket C for the support
5. Drill and insert 4 dowels appropriate for the type of wall.
6. Fix the socket to the wall using suitable screws, washers.
7. Snap the guard B onto the socket.
8. Insert the 2° adjustment plate from below again.
Adjusting the height
1. Remove the 2° adjustment plate.
2. To lower by 10 mm, insert the 0° adjustment plate E.
3. To raise by 10 mm, insert the 4° adjustment plate F.
Installing the support leg (H345 / R7764) (Fig. 2)
1. Remove the socket's guard, if fitted.
2. Remove the end cap C, if fitted or the cover on the
3. If not fitted, install the hinge piece B by sliding it onto
4. Install the front end of the guide J into the oblong hole
5. Remove the lower left-hand fixing screw G from the
6. Position the guide J on the outside of the support bar,
7. Fasten the wall hinge F using the socket's lower,
8. Insert the upper end of the support leg I into the hinge
9. Install the socket's guard.
10. Check that the whole assembly is firm and operates
Adjusting the height (Fig. 2)
1. To decrease the height of the support leg turn the foot
2. To increase the height of the support leg turn the foot
WARNING!
Risk of falling!
– Mount only to walls that have a sufficient
load-bearing capacity.
the height of the thumb's upper joint. This height
corresponds to the support bar's highest point A (middle
of support bar).
and 2 below outside) taking into account the previously
measured height.
bar accordingly.
The support bar is supplied with a 2° adjustment
plate D. To adjust the height of the support bar, use
option R7768 (3 adjustment plates of 0°, 2° and 4°).
lower tube of the support bar D.
the lower tube. If necessary, use a plastic mallet. Fix
with one screw and cover with two protective caps.
in the support leg I using a plastic mallet and starlock
retainer ring H.
socket E.
the end with the wall hinge F pointing towards the
support wall or socket E.
left-hand side fixing screw G.
piece B. Fasten it using the screw and position two
protective caps K.
correctly.
assembly L counterclockwise into the support leg I.
assembly clockwise out of the support leg.
The height of the support bar can additionally be
adjusted with the 0°, 2° and 4° adjustment plates
like described above.
5