Installing The Battery; Charging The Battery - EINHELL GE-WS 18/150 Li Instructions D'origine

3. If you have not already done so, mix the con-
centrated additive with the water (or other
liquid) by shaking the pressure sprayer.
4. Apply the name of the spray solution you are
using to the spray solution tank (e.g. by me-
ans of a sticker)

5.4 Installing the battery

Note:
•
The equipment is supplied without batteries
and without a charger.
•
The cover flap closes by itself and is held in
position by magnets.
Open and hold the cover fl ap (Fig. 6/Item 8). Push
the battery into the battery mount provided. Make
sure that the pushlock button (Fig. 6/Item C) en-
gages as soon as the battery has been pushed in
all the way. To remove the battery, proceed in the
reverse order.

5.5 Charging the battery

1. Take the battery pack out of the equipment.
To do so, press the pushlock button. (Fig. 6/
Item C).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Insert the battery pack into the charger (Fig.
7).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charger
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
Anl_GE_WS_18-150_Li_SPK9.indb 25
GB
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.6 Battery charge level indicator (Fig. 8)
Press the button for the battery charge level indi-
cator (Item A). The battery charge level indicator
(Item B) shows the charge status of the battery
using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs fl ash:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.
5.7 Using the harness (Fig. 9)
Slip the harness over your shoulders and adjust
the length of the harness so that you can work
without fatigue. To do so, pull on the two ends of
the harness to shorten it (Fig. 9 / Item 10a) or on
the two harness release mechanisms to extend it
(Fig. 9 / Item 10b).
Note: Should the fastening hooks for the harness
(Fig. 9 / Item 10c) come off , attach them back in
position again as shown in Figs. 3a-3b.
6. Operation
WARNING!
Check the equipment for damage before you use
it. Never use the equipment if it is damaged.
•
Check the tank for damage each time before
and after using the equipment.
•
Check the hose and all screw connections for
damage and leaks each time before and after
using the equipment.
- 25 -
22.10.2020 08:47:06