EINHELL GE-WS 18/150 Li Instructions D'origine page 27

cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Cleaning the inside of the container.
After use, clean the equipment and leave the con-
tainer open to dry. Note the cleaning instructions
in the directions for use that came with the chemi-
cal in addition to these cleaning instructions.
Remove any remaining liquid from the tank
through the container's fi ller opening and store
the liquid properly for subsequent use or dispose
of it in accordance with the applicable regulations.
1. Unscrew the tank lid (Fig. 5 / Item 6) from the
tank.
2. Remove the fi lling sieve (Fig. 4 / Item 7a) and
clean it with ample water as required.
3. Tilt the tank forwards and empty it completely.
4. Reinsert the fi lling sieve (Fig. 4 / Item 7a) in
the tank opening. Make sure that the seal
(Fig. 4/Item 7b) is correctly seated.
5. Screw the tank lid (Fig. 5 / Fig 6) back on the
tank.
6. Shake the pressure spray vigorously several
times.
7. Spray the contents onto the area just treated
or an area reserved for this purpose.
8. Repeat this process.
9. The container can now be drained through
the fi ller opening as described above.
10. Allow the tank to dry out completely.
Before you use the tank again, re-insert the fi lling
sieve and screw the tank lid back onto the tank.
7.3 Cleaning the intake fi lter (Fig. 15)
Clean the intake fi lter in the tank at least once a
year, ideally after the winter break or when there
are problems (see section 10). Proceed as fol-
lows:
1. Empty the tank as described in 7.2.
2. Pull the suction hose (Item 7c) with intake
fi lter off the pump connection (Item 7d).
3. Rinse the suction hose and clean the intake
fi lter (Item 7e) with a brush in clear water.
4. Refi t the suction hose (Item 7c) to the pump
connection (Item 7d) and make sure that the
intake fi lter extends to the bottom of the tank.
Only then can the tank be properly emptied
during spraying.
Anl_GE_WS_18-150_Li_SPK9.indb 27
GB
7.4 Cleaning the fi lter element in the handle
(Fig. 16-17)
Clean the fi lter element in the handle at least
once a year, ideally after the winter break or when
there are problems (see section 10). Proceed as
follows:
1. Unscrew the union nut (Item 4a) from the
handle (Item 4).
2. Pull the fi lter (Item 4b) out of the handle (Item
4) and clean it with a brush in clear water.
3. Re-insert the fi lter (Item 4b).
4. Screw the union nut (Item 4a) securely back
onto the handle (Item 4).
7.5 Cleaning the nozzle and the adjustable
spray head
Clean the nozzle and the adjustable spray head
at least once a year, ideally after the winter break
or when there are problems (see section 10). Ne-
ver blow out the nozzle or the spray head directly
by mouth. Proceed as follows:
1. Turn the adjustable spray head counterclock-
wise as far as it will go (Fig. 18).
2. Clean the exposed nozzle (Fig. 19a) and the
hole in the spray head (Fig. 19b) of residue
using a thin wire.
3. Flush the nozzle and spray head with clear
water.
4. Allow the nozzle and spray head to dry.
7.6 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.7 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
- 27 -
22.10.2020 08:47:07