Technical Data; Important; Before Starting The Equipment - EINHELL GC-CG 7,2 Li Instructions D'origine

applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Speed n0 .............................................1200 min
Cutting width of grass shears .................... 90 mm
Cutting length of shrub shears ................ 130 mm
Cutting thickness of shrub shears ............... 8 mm
Max. operating time ...................................80 min
Battery ................ Lithium-ion / 7.2 V d.c. / 1.5 Ah
Charging time ................................................. 2 h
Sound pressure level LpA .................... 63 dB (A)
Sound power level LWA ........................ 83 dB (A)
Uncertainty K ................................................ 3 dB
Vibration ah .............................................5.5 m/s
Uncertainty K ..........................................1.5 m/s
Sound pressure level at the operator's ear . 77 dB
(A)
Uncertainty K ................................................ 3 dB
Charging unit
Mains voltage ....................100-240 V ~ 50-60 Hz
Output
Rated voltage .......................................... 9 V d. c.
Rated current ....................................... 1000 mA
•
The vibration emission level has been measu-
red in accordance with a set of standardized
criteria and can be used to compare one po-
wer tool with another.
•
The specified emission level can also be
used to make an initial assessment of the ex-
posure to vibrations.

Important!

The vibration value changes according to the
area of application of the electric equipment and
may exceed the specifi ed value in exceptional
circumstances.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
Anl_GC_CG_7_2_Li_SPK7.indb 16 Anl_GC_CG_7_2_Li_SPK7.indb 16
GB
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
-1
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
2
maintained.
2

5. Before starting the equipment

5.1. Charging the battery (Fig. 3a-4a)
•
Connect the charger to the battery. Make sure
that the bead (A) of the plug is inserted into
the bottom notch (B) of the battery. You can
charge the battery when it has been removed
(Fig. 3b) but also when it is still installed (Fig.
3c). For safety reasons it is not possible to
work with the battery while it is being charged.
•
Check that your mains voltage is the same
as that marked on the rating plate. Plug the
battery charger into a socket-outlet. The LED
(Fig. 4a / Item C) will light up to indicate that
charging voltage is available.
•
The battery pack is being charged. An empty
battery pack requires a maximum charging
period of 2 hours. The temperature of the bat-
tery pack may rise slightly during the charging
operation. This is normal.
•
As soon as the battery pack is fully charged,
the LED (Fig. 4a/Item C) will no longer be lit.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
- 16 -
05.09.2016 07:20:58 05.09.2016 07:20:58