Functional Description; Removing/Inserting The Battery - Milwaukee M12 Manuel De L'utilisateur

Laser monoplan vert 360
Masquer les pouces Voir aussi pour M12:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Federal Communications Commission
WARNING
proved by the party responsible for compliance could
void the user's authority to operate the equipment.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful in-
terference in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or televi-
sion reception, which can be determined by turning
the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Consult the dealer or an experienced radio/TV
technician for help.
SPECIFICATIONS
Cat. No. ..................................................... 3631-20
Volts.............................................................. 12 DC
Battery Type .................................................M12™
Charger Type................................................M12™
Laser............................................................Class 2
Max Power........................................... P
Frequency....................................................10 KHz
Pulse Duration Normal Mode ................. T
Pulse Duration Power Save.................... T
Wavelength.......................................... 510-530 nm
Beam Divergence ........................................... 3 rad
Working Range .................................. 125' (Radius)
Range with Detector .......................... 165' (Radius)
Accuracy ...............................................±1/8" @ 33'
Settle Time ......................................... < 3 Seconds
Tripod Mount ..................................1/4"-20, 5/8"-11
Ingress Protection............................................ IP54
Drop Rating .......................................................1 m
Leveling ............Auto ±°4 side to side, front to back
Bare Tool Weight ........................................2.03 lbs
Weight ........................................................2.91 lbs
(With heaviest compatible battery pack)
Storage Temp .................................... -4°F to 120°F
Recommended Ambient
Operating Temperature .................. 14°F to 104°F
SYMBOLOGY
Changes or modifications to
this unit not expressly ap-
AVG
p
p
Volts
Direct Current
Laser Radiation
Do not stare into beam
Class 2 laser product
Magnets
Read operator's manual

FUNCTIONAL DESCRIPTION

1
8
7
6
≤ 8 mW
≤ 80 µs
1. Laser aperture
≤ 50 µs
2. Locking power dial
3. Mounting bracket
4. Threaded tripod
attachment
WARNING
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
in use.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
may be hazardous.
Power save mode is indicated by dimmed laser
beams. Visual range is decreased in power save
mode. The tool will automatically switch to power
save mode if less than 7% of battery charge remains.
*When automatically switched to power save mode
due to low battery, the tool cannot be switched back
to normal mode until the battery is charged/replaced.
3
2
5. Lanyard attachment
6. Magnets
7. Nail/screw hole
8. Fuel gauge
ASSEMBLY
Recharge only with the charger
specified for the battery. For spe-
Always lock the tool or remove the
battery pack any time the tool is not
Only use accessories specifically
recommended for this tool. Others
Power Save Mode
3
4
5

Publicité

Table des Matières
loading

Table des Matières