Table Des Matières; Functional Description - Delta 36-6013 Manuel D'utilisation

FUNCTIONAL DESCRIPTION...............................................2
IMPORTANT SAFETY INSTRUCTIONS.................................3
SAFETY-SYMBOLS-DEFINITIONS...............................3
GENERAL SAFETY RULES.....................................................4
TABLE SAW SAFETY RULES.................................................5
TERMINOLOGY............................................................5
GENERAL POWER TOOL SAFETY..........................................5
SAW BLADE GUARD, ANTI-KICKBACK PAWLS AND RIVING
KNIFE ASSEMBLY.................................................................6
MAKING A PUSH STICK ......................................................6
KICKBACKS ........................................................................6
PROPOSITION 65 WARNING.............................................7
POWER CONNECTIONS.......................................................7
POWER SOURCE..................................................................7
EXTENSION CORDS.............................................................8
UNPACKING.......................................................9
PACKAGE CONTENTS...........................................................9
CONTENTS OF HARDWARE BAGS ......................................10
ASSEMBLY.........................................................10
HEIGHT ADJUSTMENT KNOB INSTALLATION ......................11
BLADE AND GUARDS ...................................................11
ATTACH THE BLADE ..................................... . . . . . . . . . . . . . . . 1 1
INSERT THROAT PLATE ...............................................13
ANTI-KICKBACKS PAWLS AND BLADE GUARD . . . . . . . . . . . . . . . 1 5
ONBOARD STORAGE ...................................................17
OPERATION......................................................................18
TURNING THE SAW ON/OFF .............................................19
MAKING CUTS...................................................................20
RIP CUTS..........................................................................21
BEVEL RIPPING.................................................................21
CROSSCUTTING...............................................................22
BEVEL CROSSCUTTING......................................................22
MITER CUTS......................................................................22
COMPOUND MITER CUTS...................................................23
LARGE PANEL CUTS...........................................................23
NON-THROUGH CUTS........................................................23
The DELTA #36-6013 series 10-inch Contractor Table Saw is
®
designed for portability and high quality performance. It includes:
basic machine, sturdy tubular steel stand, integral 2 1/2" dust
chute, a fence system, T-slot miter gauge, 15-amp motor, on/off
switch, cast aluminum table, extension wing, see-through blade
guard with anti-kickback fingers, and 10-inch carbide blade.
This tool can only be used with woodworking saw blades.
NOTICE: The manual cover illustrates the current production model. All other illustrations contained in the manual are representative
only and may not be exact depictions of the actual labeling or accessories included. They are intended for illustrative purposes only.
IMPORTANT SAFETY INSTRUCTIONS
CAREFULLY READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS ON YOUR PRODUCT AND IN
THIS MANUAL. SAVE THIS MANUAL. MAKE SURE ALL USERS ARE FAMILIAR WITH IT'S WARNING AND
INSTRUCTIONS WHEN USING THE TOOL. Improper operation, maintenance or modification of tools or equipment could result in
serious injury and/or property damage.
If you have any questions or concerns relative to the use of your tool or the contents of this manual, stop using the tool and contact
DELTA Power Equipment Corporation Customer Care at 1-800-223-7278.
®
TABLE OF CONTENTS

FUNCTIONAL DESCRIPTION

MAKING A NON-THROUGH CUT...........................................23
CUTTING AIDS AND ACCESSORIES...............................24
PUSH STICK......................................................................24
AUXILIARY MITER GAUGE FACING.....................................25
PUSH BLOCK.....................................................................25
FEATHERBOARD................................................................26
CUT OFF GAUGE...............................................................26
JIGS......................................................................26
MAKING ADJUSTMENTS..................................................27
LEVELING THE THROAT PLATE .........................................27
SQUARING THE BLADE VERTICALLY TO THE TABLE...........27
ADJUSTING THE BEVEL STOPS...........................................28
ADJUSTING THE BLADE HEIGHT........................................29
CHANGING THE BEVEL......................................................29
USING THE MITER GAUGE...................................................30
INSTALLING THE FENCE....................................................31
ADJUSTING THE RAIL SYSTEM...........................................32
RIVING KNIFE POSITION AND ALIGNMENT.................33
RIVING KNIFE HEIGHT SETTING.........................................33
RIVING KNIFE ALIGNMENT.................................................34
MAINTENANCE.......................................................36
TROUBLESHOOTING.............................................36
ACCESSORIES..................................................37
WARRANTY......................................................37
FRENCH........................................................................38
SPANISH.........................................................................74
SPECIFICATIONS
Max depth of cut at 90 degrees:
Max depth of cut at 45 degrees:
Max rip to right of blade:
Max rip to left of blade:
MOTOR SPECIFICATIONS:
Amps
Voltage
2
3-1/2"
2-1/2"
25"
12"
15
120