Before Starting Up; Assembly - Scheppach 5906821901 Traduction Des Instructions D'origine

• Try to keep the stress as low as possible. For exam-
ple: Limit working time. In doing so, all parts of the
operating cycle must be taken into account (such
as times in which the electric tool is switched off or
times in which it is switched on, but is not running
under a load).

7. Before starting up

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
• Before connecting the machine, make certain that
the data on the type plate matches with the mains
power data.
• Check the device for transport damage. Immedi-
ately report any damage to the transport company
that delivered the electrical tool.
• Long supply cables (extension cable) should be
avoided.
• Do not operate the electrical tool in damp or wet
areas.
• Operate the electrical tool only in suitable areas
(well ventilated).

8. Assembly

m Attention!
Always make sure the device is fully assembled be-
fore start-up!
m Before connecting the machine to the mains
power, make certain that the data on the type plate
matches with the mains power data.
m Warning!
Always pull out the mains plug before carrying out
adjustments on the device.
8.1 Assembling the base plate and column (fig. 2)
1. Slide the quick clamp (2) over the column (3).
2. Set the column (3) into the base plate (1) such that
the guide pins on the bottom end of the column
(3) engage with the groove in the mount on the
base plate (1).
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
3. Tighten the pre-assembled fastening screws (A)
on the rear of the base plate (1) with the Allen key
(19).
8.2 Fitting the parallel stop (fig. 2)
1. Slide the parallel stop (16) into the grooves in the
base plate (1).
2. Ensure that the sliding blocks underneath the
wing screws of the parallel stop (15) are properly
engaged in the grooves of the base plate.
3. Move the parallel stop (16) to the desired position
and tighten the wing screws of the parallel stop
(15) firmly.
8.3 Assembling the chuck guard (fig. 3)
1. Insert the chuck guard (13) into the holes provided
in the machine frame.
2. Secure the chuck guard (13) by hand-tightening
the screws (C).
8.4 Assembling the handle (fig. 4)
The handle (8) can be mounted on the right-side of
the machine for right-handers and on the left-side of
the machine for left-handers.
When installing the handle (8), ensure that the availa-
ble mating surfaces engage.
1. Slide the mounting mandrel (8.1) onto the handle
(8).
2. Fit the spacer sleeve (8.2) to the mounting man-
drel (8.1).
3. Fit the handle (8) with the mounted mounting
mandrel (8.1) and the spacer sleeve (8.2) to the
retainer (D).
4. Fasten the handle (8) using the Philips screw (B).
5. Attach the handle cover (8.3) to the handle (8).
To disassemble the handle (8), remove the handle
cover (8.3).
Now remove the handle (8) in reverse order.
8.5 Assembling the depth stop (fig. 5)
Insert the depth stop (7) into the hole provided in the
housing.
8.6 Assembling the clamping lever for depth stop
(fig. 5)
Assemble the clamping lever for depth stop (6) as
shown in fig. 5.
8.7 Fastening to a work surface (fig. 6)
Fasten the device to the work surface by bolting the
base plate (1) to the work surface.
The table mounting attachment kit (E) can be used
for this.
GB | 25