Intended Use; Safety Instructions - Scheppach 5906821901 Traduction Des Instructions D'origine

Perceuse à colonne
Masquer les pouces Voir aussi pour 5906821901:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 30

4. Intended use

The bench drill is designed for drilling in metal, wood,
plastic and tiles.
Chuck clamping range: 1.5 - 13 mm.
The device is intended to be used by do-it-your-
selfers. It was not designed for heavy commercial
use. The tool is not to be used by persons under the
age of 16. Children over the age of 16 may use the
tool except under supervision.The manufacturer is
not liable for damage caused by an improper use or
incorrect operation of this device.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial appli-
cations. Our warranty will be voided if the equipment
is used in commercial, trade or industrial businesses
or for equivalent purposes.

5. Safety instructions

General power tool safety warnings
m WARNING Read all safety warnings, instruc-
tions, illustrations and specifications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future ref-
erence.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-oper-
ated (cordless) power tool.
Work area safety
a. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive at-
mospheres, such as in the presence of flam-
mable liquids, gases or dust.
Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while op-
erating a power tool.
Distractions can cause you to lose control.
Electrical safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
22 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
b. Avoid body contact with earthed or ground-
ed surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk
of electric shock if your body is earthed or
grounded.
c. Do not expose power tools to rain or wet con-
ditions.
Water entering a power tool will increase the risk
of electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords in-
crease the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f. If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or med-
ication.
A moment of inattention while operating power
tools may result in serious personal injury.
b. Use personal protective equipment. Always
wear eye protection.
Protective equipment such as a dust mask, non-
skid safety shoes, hard hat or hearing protection
used for appropriate conditions will reduce per-
sonal injuries.
3. Prevent unintentional starting. Ensure the
switch is in the off-position before connect-
ing to power source and/or battery pack, pick-
ing up or carrying the tool.
Carrying power tools with your finger on the switch
or energising power tools that have the switch on
invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e. Do not overreach.
Keep proper footing and balance at all times. This
enables better control of the power tool in unex-
pected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away
from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Dp60

Table des Matières