Bosch EXACT ION 6-1500 WK 18 V-LI Notice Originale page 18

OBJ_BUCH-2165-002.book Page 18 Tuesday, February 24, 2015 10:11 AM
18 | English
Mounting the Angled Screw Head (see figure D)
On these industrial cordless angle wrenches, a fitting angled
screw head (see "Angled drive head", page 16) has to be
mounted first.
– Hold the power tool with the open-end spanner 22 by the
spanner flats 4 of the angled head flange.
 Never clamp the tool by the housing shells!
– Mount the angled screw head 3 onto the flange in the re-
quested position and tighten the sleeve nut with the open-
end spanner 21 via the spanner flats 5.
Hold the angled head flange with the open-end spanner 22
to prevent turning.
Adjusting the Angled Drive Head
The angled drive head 3 can be adjusted to a total of eight po-
sitions.
– Hold the power tool with the open-end spanner 22 by the
spanner flats 4 of the angled head flange.
 Never clamp the tool by the housing shells!
– Loosen the sleeve nut with the open-end spanner 21 by
the spanner flats 5. Adjust the angled drive head 3 in 45°
steps to the desired position and retighten the sleeve nut
again with the open-end spanner 21 by the spanner flats 5.
Hold the angled head flange with the open-end spanner 22
to prevent turning.
Changing Application Tools on the Screw Head
with External Square Drive (see figure E)
Inserting
– Press in the pin on the drive square of the tool holder 2,
e. g. using a small screwdriver, and slide the tool bit 1 over
the drive square. Pay attention that the pin engages in the
recess of the tool bit.
Removing
– Press in the pin in the recess of the tool bit 1 and pull the
tool bit out of the tool holder 2.
Changing Application Tools on the Screw Head
with Internal Hexagon (see figure F)
Inserting
– Insert the tool bit 1 into the internal hex socket of the tool
holder 2 until it can be felt to engage.
Removing
– Pull the tool bit 1 off of the tool holder 2 with the aid of pli-
ers, if necessary.
Changing Application Tools on the Head with
Quick-change Chuck (see figure G)
Inserting
Use only insertion tools with fitting end pieces
(1/4" hexagonal).
– Pull the sleeve of quick-change chuck 23 to the front and
hold.
– Insert tool bit 1 into tool holder 2 and release the quick-
change chuck.
1 609 92A 139 | (24.2.15)
Removing
– Pull the sleeve of quick-change chuck 23 to the front and
hold.
– Remove tool bit 1 from tool holder 2 and release the quick-
change chuck.
Operation
 Before any work on the power tool, remove the battery.
Starting Operation
When starting the power tool, you should first select the di-
rection of rotation with the rotational direction switch 9 since
the power tool starts only when the rotational direction switch
9 is not in the middle position (switch-on lock).
Reversing the rotational direction (see figure H)
– Right rotation: For driving in screws, push the rotational
direction switch 9 left to the stop.
– Left Rotation: For loosening or unscrewing screws, push
the rotational direction switch 9 right to the stop.
Switching On the Worklight
The work area illumination 6 makes possible the lighting of
the screwing position for unfavorable light conditions. The
work area illumination 6 is switched on by lightly pressing the
on/off switch 8. When the on/off switch is firmly pressed, the
power tool is switched on and the work area illumination con-
tinues to light.
 Do not look directly into the work area illumination –
your sight can be temporarily degraded!
Switching On and Off
The screwdriver have a shut-off clutch that
depends on the torque and can be set in the
given range. It responds when the torque that
is set is reached.
– To start the machine press the on/off switch 8 to the stop.
– The machine switches off automatically as soon as the
preset torque is reached.
 When the on/off switch 8 is released prematurely, the
preset torque is not reached.
To save energy, only switch the power tool on when using it.
Working Advice
 Apply the power tool to the screw/nut only when it is
switched off. Rotating tool inserts can slip off.
Setting the Torque (see figure I)
The tightening torque is dependent on the spring pretension
of the shut-off clutch. The shut-off clutch responds in right as
well as left rotation when the torque setting is reached.
For setting the individual tightening torques, use only the ad-
justment tool 24 provided.
– Push the torque selector switch 7 on the power tool com-
pletely back.
– Insert a hex key 25 into tool bit 1 and turn it slowly.
Bosch Power Tools