DeWalt DC628 Guide D'utilisation page 8

632246-00,01,DC628 8/29/06 6:26 PM
Loading the Tool
WARNING: Keep the tool pointed away from yourself and
others. Serious personal injury may result.
WARNING: Never load nails with the contact trip or trig-
ger activated. Personal injury may result.
WARNING: Always remove battery pack before loading or
unloading nails. Serious personal injury may result.
LOAD AND DRAW METHOD (FIG. 1)
1. Insert fasteners into the rear of the magazine (G).
2. Pull pusher (H) back until the nail follower falls behind
the nails.
3. Release the pusher.
LOCK AND LOAD METHOD
CAUTION: Keep fingers clear of pusher to prevent injury.
CAUTION: The contact trip lock-off should always be
locked off whenever any adjustments are made or when tool
is not in use.
1. Pull pusher back until it locks.
2. Insert fasteners into the rear of the magazine.
3. Push forward on the pusher until it releases and slides
forward.
UNLOADING THE TOOL
CAUTION: The contact trip lock-off should always be
locked off whenever any adjustments are made or when tool
is not in use.
1. Pull pusher back until it locks.
2. Tip the tool up until the nails slide freely out the back of
the magazine
3. Open the jam clear door on the nosepiece to verify there
are no nails remaining.
Adjusting Depth (Fig. 10)
The depth that the fastener is driven can be adjusted using
the depth adjustment wheel (C) on the side of the tool.
WARNING: To reduce risk of serious injury from acci-
dental actuation when attempting to adjust depth,
ALWAYS:
• Remove battery pack.
• Engage contact trip lock-off.
• Avoid contact with trigger during adjustments.
1. To drive the nail shallower, rotate the depth adjustment
wheel (C) counterclockwise. There are six depth settings,
1 being the shallowest and 6 being the deepest.
2. To sink a nail deeper, rotate the depth adjustment wheel
(C) clockwise.
Page 6
FIG. 10
C
Headlights (Fig. 10)
There is a headlight (D) located on each side of the nailer.
Headlights turn on upon battery insertion, activation of the
trigger, or depressing the contact trip. The lights will automat-
ically shut off after 10 seconds unless tool remains in use.
NOTE: These headlights are for lighting the immediate work
surface and are not intended to be used as flashlights.
LOW BATTERY INDICATOR: The headlights will flash four
consecutive times and then shut down to indicate low battery.
JAMMED NAIL INDICATOR: The headlights will flash con-
tinually if a nail becomes jammed in the nosepiece (see
Clearing a Jammed Nail).
Clearing a Jammed Nail (Fig. 11)
If a nail becomes jammed in the nosepiece, keep the tool
pointed away from you and follow these instructions to clear:
1. Remove battery pack from tool and engage contact trip
lock-off.
2. Pull the pusher back until it locks in place then remove
the nails.
3. Lift the jam clearing latch (E) then
pull up to open front door (O).
4. Remove bent nail, using pliers if
necessary.
5. If driver blade is in the down
position, insert screwdriver or
other rod into nosepiece and
push driver blade back in position.
6. Close the front door and engage
the wireform under the 2 arms (N) on the nosepiece.
Push latch until it locks in place.
7. Reinsert battery pack.
NOTE: The tool will disable itself and not reset until the
battery pack has been removed and reinserted.
8. Reinsert nails into magazine (see Loading the Tool).
9. Release pusher.
NOTE: Should nails continue to jam frequently in nosepiece,
have tool serviced by an authorized D
D
FIG. 11
N
E
O
WALT service center.
E
6
Cold Weather Operation
When operating tools at temperatures below freezing:
1. Keep tool as warm as possible prior to use.
2. Actuate the tool 5 or 6 times into scrap lumber before
using.
Hot Weather Operation
Tool should operate normally. However, keep tool out of direct
sunlight as excessive heat can deteriorate bumpers and other
rubber parts resulting in increased maintenance.
Suspension Hook (Fig. 12)
The D WALT cordless nailers include an
E
integrated suspension hook (J) and can be
attached to either side of the tool to accom-
modate left- or right-handed users.
If the hook is not desired at all, it can be
removed from the tool.
TO REMOVE SUSPENSION HOOK
1. Remove battery pack from tool.
2. To switch the tool from right- to left-hand usage simply
remove the screw from the opposite side of the tool and
reassemble on the other side.
3. Replace battery pack.
WARNING: Remove nails from magazine before making
any adjustments or servicing this tool. Failure to do so may
result in serious injury.
CAUTION: Disconnect battery pack from tool before
making any adjustments, changing accessories, servic-
ing, or moving the tool. Such preventative safety measures
reduce the risk of starting the tool accidentally.
CAUTION: When not in use, place tool on its side on a
stable surface where it will not cause a tripping or falling
hazard. Some tools with large battery packs will stand
upright on the battery pack but may be easily knocked over.
MAINTENANCE
WARNING: Disconnect battery pack from tool before
cleaning and inspection. Make sure tool is in proper working
condition before placing the tool back in use or serious
personal injury may result.
Daily Maintenance Chart
ACTION Clean magazine, pusher, and contact trip mechanism.
WHY Permits smooth operation of magazine, reduces wear,
and prevents jams.
HOW The use of oils, lubricants periodically or solvents is not
recommended as they tend to attract debris.
ACTION Before each use, check to insure all screws, nuts and
fasteners are tight and undamaged.
WHY Prevents jams and premature failure of tool parts.
HOW Tighten loose screws or other fasteners using the
appropriate Allen wrench or screwdriver.
FIG. 12
J