Technical Data - Parkside PKGA 20-Li B1 Traduction Des Instructions D'origine

Technical Data

4-in-1 Cordless
combination tool ................. PKGA 20-Li B1
Motor voltage ............................. 20 V
Idling speed (n ) ....................21000 min
0
Motor unit with drill attachment ..... PKGA1
Idling speed (n ) ........ 0-400/0-1350 min
0
Torque ................................ max. 25 Nm
Spread drill chuck .................. 1.0-10 mm
Drill diameter
for wood .......................... max. 10 mm
for steel ............................. max. 8 mm
Weight (without charger)................1.5 kg
Sound pressure level
(L ) ................... 83.7 dB(A), K
pA
Sound power level
(L ) ................. 94.7 dB(A), K
WA
Vibration (a )
h
drilling in metal .................. 1.322 m/s
idling ................................ 1.531 m/s
Motor unit with multisander
attachment .................................... PKGA2
Oscillation rate (n
0
Sanding sheet size
Weight (without charger)................1.4 kg
Sound pressure level
(L ) ................... 88.6 dB(A), K
pA
Sound power level
(L ) ................. 99.6 dB(A), K
WA
Vibration (a ) ......4.572 m/s
h
Motor unit with sabre saw
attachment .................................... PKGA3
Stroke rate (n ) .....................0-3200 min
0
Stroke length
Weight (without charger)................1.8 kg
Sound pressure level
(L ) ................... 89.3 dB(A), K
pA
= 3 dB
pA
= 3 dB
WA
K=1.5 m/s
) ..............0-9000 min
.......138 x 97 mm
= 3 dB
pA
= 3 dB
WA
, K=1.5 m/s
2
...................... 22 mm
= 3 dB
pA
Sound power level
(L ) ............... 100.3 dB(A), K
WA
Vibration (a )
h
Sawing boards ................ 12.395 m/s
Sawing wood beams ........ 12.392 m/s
-1
Motor unit with multifunction tool ... PKGA4
-1 Oscillation rate (n
Oscillation angle ..............................3.0°
Weight (without charger)................1.4 kg
Sound pressure level
(L ) ................... 84.8 dB(A), K
pA
Sound power level
(L ) ................. 95.8 dB(A), K
WA
Vibration (a ) ......4.229m/s
h
The stated vibration emission value was
measured in accordance with a standard
testing procedure and may be used to com-
pare one power tool to another.
2
2 The stated vibration emission value may
also be used for a preliminary exposure
2
assessment.
Warning: The vibration emission
value may differ during actual use
-1
of the power tool from the stated
value depending on the manner in
which the power tool is used.
Try to keep the exposure to vibra-
tions as low as possible. Examples
of measures to reduce vibration
exposure are the wearing of gloves
2
when using the tool (except: operat-
ing mode drilling) and limiting the
working hours. For this purpose all
-1 parts of the operating cycle have to
be considered (for example, times
when the electric tool is switched
off and times when it is switched on
but running without any load).
GB
WA
K=1.5 m/s
) ............0-20000 min
0
pA
WA
2 , K= 1.5 m/s
IE
= 3 dB
2
2
2
-1
= 3 dB
= 3 dB
2
31