Fitting And Removing The Display - Gazelle Shimano Steps-system Démarrage Rapide

purchase for details.
„ Installing and removing the cycle computer
The cycle computer can also be secured to the bicycle so that it cannot be easily removed. Please contact your place of
Installing
purchase for details.
1.
Slide the cycle computer onto the bracket.
Installing
2.
Insert the cycle computer securely until it clicks into
place.
1.
Slide the cycle computer onto the bracket.
2.
Insert the cycle computer securely until it clicks into
.

Fitting and removing the display

place.
If the cycle computer is not correctly installed, the assist function
will not operate normally.
Fit the display by sliding it into its mount; see
If the cycle computer is not correctly installed, the assist function
illustration.
will not operate normally.
Slide the display into the holder until it clicks
in place. The assistance will not work
satisfactorily if the display is not fitted correctly.
You remove the display by pressing on the
mount lever and sliding the display out of the
Operation
mount.
You should remove the display from the display
Removing
„ Turning the power ON / OFF
holder before adjusting the handlebar stem.
1.
• The power cannot be turned on while charging.
Slide out the cycle computer.
• Push the lever firmly to release the cycle computer.
• If the bicycle has not moved for over 10 minutes, the power will automatically turn off (automatic power off function).
Removing
If you fail to observe this instruction,
you run the risk of the display falling
1.
Slide out the cycle computer.
out of its holder while adjusting the handle-
• Push the lever firmly to release the cycle computer.
Do not place your foot on the pedals when turning ON/OFF. This may cause a system error. bar stem.
Powering on using the cycle computer with the cycle computer
. Switching the power on and o via the display
• If the built-in battery of the cycle computer isn't charged sufficiently, it will not power on.
• The built-in battery of the cycle computer only charges when the cycle computer screen is on.
1. The system can be powered up and
Hold down the power button for 2 seconds.
powered down via the display and the
battery.
Power the system up or power it down by
pressing and holding the on/o button for
two seconds.
Powering on from the battery with the battery
It is possible to forcibly power off BT-E8010/BT-E8020 by holding down the power button for 6 seconds.
. Switching the power on and o via the battery
1.
Press the power button on the battery. The LED lamps will light up indicating remaining battery capacity.
Press the -button once to power the
system up or power it down. All indicator
lights will light up when the battery is
When turning on the power, check that the battery is firmly attached to the battery mount.
switched on.
<BT-E6000/BT-E6001>
The system cannot be switched on
Power button
while charging.
<BT-E6010>
GAZ_Snelstart Shimano Steps_21_E02_V01.indd 59
NOTE
NOTE
NOTE
NOTE
Power button
Bracket
Operation
Bracket
„ Turning the power ON / OFF
• The power cannot be turned on while charging.
• If the bicycle has not moved for over 10 minutes, the power will automatically turn off
Do not place your foot on the pedals when turning ON/OFF. This may cause a system error.
Powering on using the cycle computer with the cycle computer
• If the built-in battery of the cycle computer isn't charged sufficiently, it will not power
Lever
• The built-in battery of the cycle computer only charges when the cycle computer screen
1.
Hold down the power button for 2 seconds.
Lever
24
24
Powering on from the battery with the battery
It is possible to forcibly power off BT-E8010/BT-E8020 by holding down the power button
1.
Press the power button on the battery. The LED lamps will light up indicating remaini
Display E
When turning on the power, check that the battery is firmly attached to the battery mount.
<BT-E6000/BT-E6001>
Power button
<BT-E8010/BT-E8014>
<BT-E6010>
Power button
Power button
<BT-E8020>
EN
NOTE
Power button
NOTE
<BT-E8010/BT-E8014
<BT-E8020>
31-08-2021 09:44
Power button
Power button