Gazelle Shimano Steps-system Démarrage Rapide page 56

System individually supplies assist power to detect gear position.
controlled by the gear position.
"Intelligent walk assist" support rider more torque output in steep climb condition in lower side gears.
• If Assist-Y is not pressed for at least one minute, the system will restart in the mode that was set prior to setting [WALK]
"Quick walk assist" function works quickly by holding down SW from any mode.
mode.
• The intelligent walk assist function activates when an electric shifting system such as XTR, DEORE XT SEIS is connected.
Switch to walk assist mode
System individually supplies assist power to detect gear position.
"Intelligent walk assist" support rider more torque output in steep climb condition in lower side gears.
1.
Press and hold Assist-Y (about 2 seconds) until the
"Quick walk assist" function works quickly by holding down SW from any mode.
following occurs.
Walk assist mode
SC-E6100/SC-E7000: [WALK] is displayed on the screen
Switch to walk assist mode
• The walk assist function operates at a maximum of
EW-EN100: LED1 lights up blue
„ Walk assist mode
the assist level and speed are controlled by the gear position.
1.
Press and hold Assist-Y (about 2 seconds) until the
• This mode may not be available in certain regions.
following occurs.
• The walk assist function operates at a maximum of 6 km/h. During electronic gear shifting, the assist level and speed are
• If Assist-Y is not pressed for at least one minute, the system will restart in the mode that
SC-E6100/SC-E7000: [WALK] is displayed on the screen
controlled by the gear position.
was set prior to setting [WALK] mode.
EW-EN100: LED1 lights up blue
• If Assist-Y is not pressed for at least one minute, the system will restart in the mode that was set prior to setting [WALK]
mode.
• The intelligent walk assist function activates when an electric shifting system such as XTR, DEORE XT SEIS is connected.
System individually supplies assist power to detect gear position.
"Intelligent walk assist" support rider more torque output in steep climb condition in lower side gears.
"Quick walk assist" function works quickly by holding down SW from any mode.
Switch to walk assist mode
Switch to walk assist mode
1.
. Press and hold Assist-Y (about
A warning tone will sound while switching is in progress if it is
Press and hold Assist-Y (about 2 seconds) until the
not possible to switch to [WALK] mode because the current
seconds) until the following occurs.
following occurs.
speed is not [0 km/h] or there is pressure on the pedals etc.
SC-E6100/SC-E7000: [WALK] is displayed on the screen - SC-E
NOTICE
EW-EN100: LED1 lights up blue
displayed on the screen
- EW-EN
A warning tone will sound while switching is in progress if it is
not possible to switch to [WALK] mode because the current
speed is not [0 km/h] or there is pressure on the pedals etc.
A warning tone will sound while
switching is in progress if it is
not possible to switch to [WALK] mode
because the current speed is not [0 km/h]
or there is pressure on the pedals etc.
A warning tone will sound while switching is in progress if it is
not possible to switch to [WALK] mode because the current
speed is not [0 km/h] or there is pressure on the pedals etc.
GAZ_Snelstart Shimano Steps_21_E02_V01.indd 56
Assist
Assist
NOTICE
/SC-E : [WALK] is
: LED lights up blue
Assist
NOTICE
35
km/h. During electronic gear shifting,
< SC-E6100 >
< SC-E7000 >
< SC-E6100 >
< SC-E7000 >
Assist OFF
< EW-EN100 >
Assist OFF Walk assist mode enabled
LED1
35
< EW-EN100 >
Assist OFF
35
< SC-E6100 >
< SC-E7000 >
< EW-EN100 >
Walk assist mode enabled
LED1
Walk assist mode enabled
LED1
31-08-2021 09:44