Initial Operation; Cleaning - Scheppach HS410 Traduction Des Instructions D'origine

Rocker extension (16) (fig. 20)
Slide the rocker extension (16) into the opening on
the left side of the rocker and align it correctly in order
for the firewood to sit firmly. Then tighten the rocker
extension with the Wing screw (20).
Longitudinal stop (15) (fig. 21)
Screw the wing screw (8) into the intended position
on the right rear of the swivel frame (insofar as this
is not already fitted).
This wing screw serves to fasten the stop (15) in
position
Before starting the equipment
On/Off switch (3) (fig. 1)
Turning on
Press green button I.
Turning off
Press red button O.

10. Initial operation

Before commissioning observe the safety notes.
• All safety and auxiliary installations must be fitted.
• Check the rocker inlet for wear and replace it if nec-
essary.
• Check the rocker that it returns to its home position
autonomously.
• Check the saw blade for perfect fitting and correct
direction of rotation.
• Changeover, setting, measuring and cleaning op-
erations are only to be conducted with the motor
switched off. Pull the mains plug and wait for the
rotating tool to come to halt.
• The saw is constructed solely for the cross cutting
of firewood.
• Regardless of the diameter of the wood only one
work piece is to be put on the rocker.
• ATTENTION! Do not saw faggots or multiple pieces
at once.
• Put curved wood on the rocker in such a way that
the curved-out side is directed to the saw blade.
• Ensure the machine is securely placed on solid
ground.
Sawing
1. Turn on the machine.
2. Wait until the saw blade has reached full speed.
3. Put the wood on the rocker.
4. Take hold of both handle bars of the rocker with
both hands and lead it evenly to the saw blade;
thus the saw blade is revealed.
5. Push the rocker evenly to ensure the engine
speed does not drop.
6. Remove the sawn wood from the rocker before
putting on the next piece.
26 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
ATTENTION!
Do not leave the machine unattended during oper-
ation.
Turn off the machine if you discontinue working, and
pull the mains plug.
Electrical connection
The electrical motor installed is connected and ready
for operation. The connection complies with the ap-
plicable VDE and DIN provisions.
The customer's mains connection as well as the ex-
tension cable used must also comply with these reg-
ulations.
Damaged electrical connection cable
The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insula-
tion damage.
Check the electrical connection cables for damage
regularly. Make sure that the connection cable does
not hang on the power network during the inspection.
Electrical connection cables must comply with the
applicable VDE and DIN provisions. Only use con-
nection cables with the marking „H07RN-F".
The printing of the type designation on the connec-
tion cable is mandatory.
For single-phase AC motors, we recommend a fuse
rating of 16A (C) or 16A (K) for machines with a high
starting current (starting from 3000 watts)!

11. Cleaning

Attention!
Pull out the power plug before carrying out any clean-
ing work on the equipment.
We recommend that you clean the equipment imme-
diately after you use it.