Unpacking; Attachment / Before Starting The Equipment; Initial Operation - Scheppach HS510 Traduction Des Instructions D'origine

Noise
m Warning: Noise can have serious effects on
your health. If the machine noise exceeds 85 dB (A),
please wear suitable hearing protection.
Characteristic noise emission values
sound power level L 115 dB(A) (EN ISO 3744)
WA
sound pressure level L 101 dB(A) (EN ISO 11201)
pA
uncertainly K 4 dB(A)
pA

8. Unpacking

Open the packaging and remove the device carefully.
Remove the packaging material as well as the pack-
aging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport
damage.
In case of complaints the dealer must be informed im-
mediately. Subsequent complaints will not be accepted.
If possible, store the packaging until the warranty pe-
riod has expired.
Read the operating manual to make yourself familiar
with the device prior to using it.
Only use original parts for accessories as well as for
wearing and spare parts. Spare parts are available
from your specialized dealer.
Specify our part numbers as well as the type and year
of construction of the device in your orders.
m ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
9. Attachment / Before starting the
equipment
m IMPORTANT!
You must fully assemble the appliance before using it
for the first time!
Assembly
Wheel axle (13) (fig. 2)
Place the wheel axle in the intended position and
secure it with the four screws, washers and nuts pro-
vided in the accessories kit.
Wheels (7) (fig. 3)
Note: Three washers are required for each side.
Push two of the three washers onto the wheel axle
you have already assembled. Then push the wheel
onto the axle. Finally, place the third washer on the
axle and fix it with the spring split pin provided.
22 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Rocker extension (14) (fig. 4)
Slide the rocker extension (14) into the opening on
the left side of the rocker and align it correctly in order
for the firewood to sit firmly. Then tighten the rocker
extension with the clamping screw (12).
Before starting the equipment
On/Off switch (8) (fig. 5)
Turning on
Press green button I.
Turning off
Press red button O.

10. Initial operation

Before commissioning observe the safety notes.
• All safety and auxiliary installations must be fitted.
• Check the rocker inlet for wear and replace it if nec-
essary.
• Check the rocker that it returns to its home position
autonomously.
• Check the saw blade for perfect fitting and correct
direction of rotation.
• Changeover, setting, measuring and cleaning op-
erations are only to be conducted with the motor
switched off. Pull the mains plug and wait for the
rotating tool to come to halt.
• The saw is constructed solely for the cross cutting
of firewood.
• Regardless of the diameter of the wood only one
work piece is to be put on the rocker.
• ATTENTION! Do not saw faggots or multiple pieces
at once.
• Put curved wood on the rocker in such a way that
the curved-out side is directed to the saw blade.
• Ensure the machine is securely placed on solid
ground.
Sawing
1. Turn on the machine.
2. Wait until the saw blade has reached full speed.
3. Put the wood on the rocker.
4. Take hold of both handle bars of the rocker with
both hands and lead it evenly to the saw blade;
thus the saw blade is revealed.
5. Push the rocker evenly to ensure the engine
speed does not drop.
6. Remove the sawn wood from the rocker before
putting on the next piece.
ATTENTION!
Do not leave the machine unattended during oper-
ation.
Turn off the machine if you discontinue working, and
pull the mains plug.