Safety Rules For Laser Lights - Ayce 3285 Manuel D'utilisation

retracting handle and make sure it moves freely and does not touch the blade
or any other part, in all angles and depths of cut.
b) Check the operation of the lower guard spring. If the guard and the spring
are not operating properly, they must be serviced before use. Lower guard
may operate sluggishly due to damaged parts, gummy deposits, or a build-up
of debris.
c) The Lower guard may be retracted manually only for special cuts such as
"plunge cuts" and "compound cuts". Raise the lower guard by the retracting
handle and as soon as blade enters the material, the lower guard must be
released. For all other sawing, the lower guard should operate automatically.
d) Always observe that the lower guard is covering the blade before placing
the saw down on bench or floor. An unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its path. Be aware of the time it
takes for the blade to stop after switch is released.
Saw Blade Safety Warnings:
1. Only use saw blades recommended, which conform to EN 847-1, and only use
saw blades if you have knowledge of how to use and handle them.
2. Pay attention to the maximum rotational speed. The maximum rotational
speed marked on the saw blade shall not be exceeded. Where stated, the
speed range shall be adhered to.
3. Do not use saw blades which are cracked. Repairing is not permitted.
4. Use the supplied saw blade only for cutting of wood, never for metal or plastic.
5. Longer period using may lead overheating the blade tips. Therefore take
breaks of approx. 15 minutes on a regular basis to let the blade tips cool down.
6. Never use any abrasive wheels.
7. The machine shall be used in a covered and dry area. The ambient
temperature shall be included between 15°C and 30°C. The humidity level
shall be less than 60%.
Residual risks
The following risks are typical for the use of this machine:
• injuries caused by touching the rotating parts, especially the blade
• injuries caused by breakage of the saw blade
In spite of the application of the relevant safety regulations, the implementation of
safety devices and the use of the tool in accordance with the instructions, several
residual risks cannot be avoided, e.g.:
• Impairment of hearing when using inappropriate hearing protection.
• Impairment of the respiratory system if no appropriate protective dust mask is
used.
• Injuries to eyes, if no appropriate protective goggles are used.
• Risk of accidents caused by the uncovered parts of the rotating cutting blade.
180731_ayce_3285_IM
• Risk of injury when changing the blade.
• Risk of squeezing fingers when opening the guards.

SAFETY RULES FOR LASER LIGHTS

The laser light used is the Class 2 with maximum 1mW power and 650nm wavelength.
These lasers do not normally present an optical hazard, although staring at the beam
may cause flash blindness.
A hazard may exist if you deliberately stare into the beam.
!
WARNING
Please observe all safety rules as follows:
- Do not stare directly at the laser beam.
- The laser shall be used and maintained in accordance with the manufacturer's
instructions.
- Never aim the beam at any person or an object other than the workpiece.
- The laser beam shall not be deliberately aimed at personnel and shall be prevented
from being directed towards the eye of a person.
- Always ensure the laser beam is aimed at a sturdy work-piece without reflective
surfaces. i.e. wood or rough coated surfaces are acceptable. Bright shiny reflective
sheet steel or the like is not suitable for laser use as the reflective surface could
direct the beam back at the operator.
- Do not attempt to change any parts of the laser guide. Do not change the laser
light assembly with a different type. Repairs must be carried out by the laser
manufacturer or an authorised agent.
- Always switch off the laser when not used.
LASER RADIATION
DO NOT STARE INTO BEAM
Class 2 Laser Product.
:650nm P < 1mW
EN60825-1:2014
92 93 |
CAUTION: Use of controls or adjustments
or performance of procedures other than
those specified herein may result in
hazardous radiation exposure.
180731_ayce_3285_IM
GB