Authorised Individuals; Preparations Prior To Starting; D.1 Connecting The Dust Extractor; D.2 Connecting A Dust-Generating Device - Renfert Silent TS Mode D'emploi

Masquer les pouces Voir aussi pour Silent TS:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 31
Regularly inspect connecting lines and hos-
es (e.g., the power cord) for damage (e.g.,
kinks, cracks, porosity) or signs of aging.
Units exhibiting damaged connecting lines,
hoses, or other defects must be taken out
of service immediately.
Always unplug the unit from the wall outlet
before beginning any work on the unit's
electrical components.
Never operate the unit without the complete
filtration system (dust bag, fine particle
filter, exhaust air filter, electronics filter).
Make sure the dust drawer is fully closed
during extraction.
Never operate the unit without the suction
hose.
Never extract flammable or explo-
sive gases, vapours, dusts.
Never extract liquids.
Never extract hot materials.
The unit may not be operated without
supervision.
All required tools must be appropriately
cleaned prior to use when the unit is
employed for medical purposes or in con-
junction with medicinal materials.
If the dust extractor is employed to extract
hazardous materials, appropriate personal
protective gear must be worn and steps
must be taken to ensure that the exhaust
air is properly ventilated. Please refer to the
associated safety data sheets for specific
requirements.
Environmentally hazardous extraction
substances. Extracted substances may be a
risk to the environment.
Dispose of extracted material according to
local statutory regulations.
It is the responsibility of the operator that
national regulations during operation and
regarding a repeated safety inspection of
electrical equipment are complied with.
For Germany these are the regulation 3 by
DGUV (German Statutory Accident Insur-
ance) in relation with VDE (Association for
Electrical & Electronic Technology) 0701-
0702.
Only spare parts and accessories supplied
or authorized by Renfert GmbH may be
used with this product. If other spare parts
or accessories are used, this could have a
detrimental effect on the safety of the de-
vice, increase the risk of serious injury and
lead to damage to the environment or the
device itself.
C. Authorised Individuals
Only properly trained individuals may operate and
service the Silent TS.
Minors or pregnant women may only operate and
service the Silent TS if they are wearing appropriate
protective gear, particularly if the unit is being used to
extract hazardous materials.
Any repairs not specifically described in these operat-
ing instructions, in particular the inspection of the suc-
tion turbine outside the unit, may only be performed
by a qualified electrician.
D. Preparations Prior to
Starting
D.1 Connecting the Dust
Extractor
The unit is supplied with a power cord and two-con-
tact plug with a ground contact (either DIN 49441 or
NEMA, depending on the particular model in ques-
tion).
The unit may not be taken into service until any
required alterations to comply with regionally specific
power plug configurations have been made.
Such alterations may only be performed by a quali-
fied electrician.
The unit may only be connected to wall outlets con-
nected to a ground circuit system.
Before operating the unit, make sure the voltage in-
formation on the nameplate corresponds to your local
power supply.
D.2 Connecting a Dust-
Generating Device
The unit is equipped with a power outlet on the back,
designed for a two-contact plug with a ground contact
(either in accordance with DIN 49441 or NEMA), to
which dust-generating equipment can be connected
(N, fig. 4).
A suitable plug is supplied for units with a nominal
voltage of 230V and plug socket according to
DIN 49441 (Fig. 32). This connector can be used to
make an adapter for your local plug configuration.
This adapter may only be made by a quali-
fied electrician!
The adapter must not interrupt the ground
circuit system!
E. Repairs
Repairs may only be performed by qualified electri-
cians or authorized dealers.
Depending on the material trapped by the filters,
protective gear may need to be worn during repairs.
- 11 -
EN

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

2921-00502921-1050

Table des Matières