Sawing - Scheppach HS116 Traduction Des Instructions D'origine

2. Set the saw blade (1) to the maximum cutting
depth. (see 11.2)
3. Position the parallel stop (8) such that the stop rail
(8a) makes contact with the saw blade (1).
4. If the stop rail (8a) is not in line with the saw blade
(1), loosen the hexagon screws (8c) in the parallel
stop (8) with a hexagon spanner and align the stop
rail (8a) parallel to the saw blade (1).
5. Tighten the hexagon screws (8c) again.
6. Again, position the parallel stop (8) away from the
saw blade (1).
11.5 Using the transverse stop (Fig. 23)
Do not push the stop rail (19b) too far towards the saw
blade (1). The distance between the stop rail (19b)
and the saw blade (1) needs to be approx. 2 cm.
11.5.1 Setting the transverse stop (fig. 23)
1. Secure the stop rail (19b) on the transverse stop
(19) by tightening the knurled nuts (19d).
2. Slide the transverse stop (19) into one of the two
guide grooves of the saw table (5).
3. Loosen the clamping handle (19c) and turn the trans-
verse stop (19) until the desired angle has been set.
4. Tighten the clamping handle (19c) again.
5. To secure the transverse stop (19) on the slid-
ing carrier plate (21), tighten the wing nut for the
transverse stop (19f).
11.5.2 Using the screw clamp on the transverse
stop (fig. 23)
1. Fit the screw clamp (19a) on the transverse stop
(19).
2. Secure the screw clamp (19a) on the required
height by tightening the wing nut for the screw
clamp (19e).
11.6 Table width extensions
11.6.1 Pulling out the left table width extension
(fig. 29)
1. To pull out the left table width extension (20), loos-
en the two wing nuts (20a) on the front and rear of
the machine.
2. Pull out the left table width extension (20) to the
desired length.
3. Secure this position by tightening the two wing
nuts (20a) again.
11.6.2 Pulling out the right table width extension
(fig. 1 + 30)
1. To pull out the right table width extension (20),
loosen the locking lever for the right table width
extension (11). (fig. 1)
2. Pull out the right table width extension (9) to the
desired length. (fig. 30)
3. Secure this position by tightening the locking lever
for the right table width extension (11) again.
40 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
11.7 Using the sliding carrier plate (fig. 31)
1. To use the sliding carrier plate (21), pull down the
wing nut (21a) and turn it 90°.
2. Release the wing nut (21a) again so that it engag-
es again.
3. The sliding carrier plate (21) is unlocked and you can
freely move it forwards and backwards.
4. To lock the sliding carrier plate (21), bring it back to
its starting position.
5. Pull the wing nut (21a) down and turn it 90° again.
6. Release it so that it engages again.
7. The sliding carrier plate (21) is locked.

12. Sawing

m WARNING
Danger of injury due to incorrect mounting
- Check that the product is properly assembled.
- Check the saw blade for mobility and the moving
parts for ease of movement.
ATTENTION
Wait after the saw has been switched on, until the
saw blade (1) has reached full speed, before starting
the cutting process.
12.1 Working instructions
m WARNING
Danger of injury!
Improper handling may result in serious injury.
- Observe and follow the safety and working in-
structions.
• When making longitudinal cuts, do not stand in front
of the circular table saw, but position yourself at an
angle to the cut.
• Always use the parallel stop for angled cuts.
• Use a push stick or wooden push block in order to
guide the workpiece past the saw blade. Replace a
damaged or worn push stick.
• Secure larger workpieces against tipping after the
cutting process. To do so, use for example a reel-
off stand.
• After the circular table saw has been switched on,
wait until the saw blade has reached full speed, be-
fore starting the cutting process.
• Only operate the table saw with an extraction system.
• After every new setting, we recommend performing
a test cut, in order to check the dimensional settings.
• Check and clean the extraction channels at regular
intervals.
12.2 Performing longitudinal cuts (fig. 32)
With a longitudinal cut, you cut a workpiece in its lon-
gitudinal direction. Hold the edge of the workpiece
against the parallel stop (8), whilst the flat side lies on
the saw table (5).
1. Adjust the parallel stop (8) according to the work-
piece height and the desired width (see 11.4).