Technical Data; Assembling The Grass Trimmer; Proper Use - EINHELL New Generation RT 325/1 Mode D'emploi

Anleitung RT 325-1 SPK 1a

4. Technical data

Voltage 230V ~ 50 Hz
Power rating
Cutting width
Speed 12.000 rpm
Nylon cutting line
Sound pressure level LPA
Sound power level
Vibration aw ≤ 2.5 m/s
Weight
The machine may exceed 85 dB (A). The operator
will require noise protection measures if this is the
case. The noise is measured in accordance with IEC
59 CO 11, IEC 704, DIN 45635 part 21, NFS 31-031
(84/538/EWG). The value of the vibrations emitted
by the handle amounts to ≤ 2.5 m/s and was
2
determined in compliance with ISO 5349.
5. Fitting the guard hood (Figs. 3-5)
Place the guard hood on the motor head as
illustrated (Fig. 3) and engage it in the bayonet
lock (Fig. 4). Make sure that the guard hood is
properly located on the grass trimmer housing.
Then secure it to the housing using the screws
provided (Fig. 5/Item a). Place the separator on
the guard hood as shown in Fig. 5a. The
separator is ideally suited for working alongside
walls (Fig. 11).

6. Assembling the grass trimmer

Place the upper section of the grass trimmer on the
motor head until it engages (Fig. 6). The motor head
can be turned 180° to enable cutting alongside
vertical surfaces. To do this, press the two snap
hooks and pull off the upper section. Turn the motor
head and assemble as shown in Fig. 8.

7. Proper use

The trimmer is designed for cutting lawns and small
areas of grass in private and hobby gardens.
Tools for private and hobby gardens are not suitable
for use in public facilities, parks and sport centers,
along roadways, on farms or in the forestry sector.
For the tool to be used properly it is imperative to
follow the instructions set out in the manufacturer's
09.09.2005 9:36 Uhr Seite 13
directions for use.
Important! It is prohibited to use the tool to chop
material for composting because of the potential
350 W
danger to persons and property.
ø 25 cm
8. Starting up
ø 1.2 mm
82 dB(A)
The grass trimmer is designed only to cut grass.
96 dB(A)
A short or worn down nylon line leads to poor cutting
quality.
2
1,65 kg
CAUTION! Make sure that you pull out the power
plug before adjusting the line length!
The nylon line must be pulled out with force when
starting up for the first time. To do this, press the
pushbutton (Fig. 15 D) and pull the line out to the
edge of the guard hood. The line will be cut to the
correct length when the cutting head starts up again
(Fig. 16).
A short or worn down nylon line leads to poor cutting
quality. To restore the correct length of line, press
the grass trimmer to the ground while the cutting
head is running. This enables the line length to
adjust itself.
To obtain maximum performance from your grass
trimmer, please follow the instructions given below:
Never use the grass trimmer without the guard.
Do not mow grass when it is wet. The best
results are achieved with dry grass.
Connect the power cable to the extension cable
and attach it in the handle (Fig. 10).
To switch the grass trimmer on, press the safety
lock-off (Fig. 9/Item 7) forwards. Then press one
of the two ON/OFF switches (Fig. 9/Item 3).
To switch off your grass trimmer, let go of the
ON/OFF switch (Fig. 9/Item 3).
Do not allow the grass trimmer near the grass
until the switch is pressed, i.e. the grass trimmer
is in operation.
To cut properly, swing the machine sideways
while moving forwards. Keep the grass trimmer
inclined at an angle of approx. 30° while you do
so (see Figs. 17 and 18).
If the grass is long, the grass must be cut shorter
in stages, starting from the tip (see Fig. 19).
Use the guard hood to prevent unnecessary
wear on the line.
To avoid unnecessary wear on the line, keep the
grass trimmer away from hard objects.
GB
13