Replacing The Blades; Ordering Spare Parts; Storage - EINHELL FREELEXO Instructions D'origine

the update. The time LEDs (50) show the cur-
rent progress. When all 5 time LEDs (50) are
lit together, this means that the process has
been completed and the robot lawn mower
will switch to its normal operating state.
5. Pull out the USB stick.
7.3 Maintenance
•
Worn or damaged blades (10) and their fas-
tening screws must always be replaced as a
set.
•
Replace excessively worn or damaged parts
immediately.
•
In order to ensure that you enjoy the equip-
ment for many years to come, all screwed
parts, as well as the wheels and axles, should
be cleaned and lubricated.
•
Keeping your robot lawn mower in good
condition not only ensures a long lifespan
and high performance, but also enables the
equipment to thoroughly cut your grass with
minimal effort.
•
The blades (10) are subject to more wear and
tear than any other component. Therefore,
routinely check the condition of the blades
(10) and make sure that they are tightly fas-
tened. An excessively vibrating robot lawn
mower can indicate that the blades (10) are
damaged or have become deformed from
striking an object. If the blades (10) are worn
or damaged, they must be replaced immedia-
tely.
•
There are no other parts inside the equipment
which require maintenance.

7.4 Replacing the blades

Only replace the blades with genuine blades, as
this will ensure top performance and safety.
The robot lawn mower is equipped with three bla-
des (10) fi tted to a blade plate (11). These blades
(10) have a service life of up to 3 months (if they
do not strike any obstacles). Please replace all
three blades (10) at the same time to ensure that
there is no possibility of any impairment to the
effi ciency and balance of your equipment.
To change the blades (10), proceed as follows
(Fig. 12):
1. Undo the fastening screws
2. Remove the blades (10) and replace them
with new ones. Always replace all three bla-
des (10) as a set.
3. Then retighten the fastening screw. Check
that the new blades (10) are able to rotate
freely.
Anl_FREELEXO_Kit_500_SPK9.indb 41 Anl_FREELEXO_Kit_500_SPK9.indb 41
GB
Perform a general inspection of the robot lawn
mower at regular intervals and remove any depo-
sits which may have accumulated. At the start of
each season, ensure that you check the condition
of the blades (10). If repairs are necessary, please
contact our customer service center. Use only
genuine spare parts.
7.5 Repairing the perimeter wire
If the perimeter wire (18) gets severed at any
point, use the supplied cable connectors (16) to
repair it. To do so, insert both ends of the severed
perimeter wire (18) into the cable connector (16)
and squeeze it together with the help of a pair of
pliers. Connect the power plug to the socket out-
let. Then check whether it is working properly by
checking the LED indicator (21) on the charging
station (19).

7.6 Ordering spare parts

Please provide the following information when
ordering spare parts:
•
Type of unit
•
Article number of the unit
•
ID number of the unit
•
Spare part number of the required spare part
For our latest prices and information please go to
www.Einhell-Service.com
Replacement blades Art. No.: 34.140.20

8. Storage

Fully charge up the rechargeable battery (22) be-
fore putting it into storage over winter and switch
off the robot lawn mower at the main switch (7)
(OFF). Take the rechargeable battery (22) out
of the equipment. Disconnect the power supply
unit (13) from the power supply and the charging
station (19).
The perimeter wire (18) can be left outdoors over
winter. However, make sure that the connections
are protected against corrosion. To do so, discon-
nect the connections of the perimeter wire (18)
from the charging station (19).
Store the equipment and accessories out of
children's reach in a dark and dry place at above
freezing temperature. The ideal storage tempera-
ture is between 5 and 30°C. Store the equipment
in its original packaging.
- 41 -
14.11.2019 12:22:53 14.11.2019 12:22:53