Starting Procedure - EINHELL FREELEXO Instructions D'origine

6.4 Locking mechanism / PIN
The locking mechanism prevents the unautho-
rized use of the robot lawn mower without a valid
code. You have to enter a personal four-digit secu-
rity code for this.
Lock release
- Before you start using the robot lawn mower,
you have to enter the correct PIN (standard
PIN: "1-2-3-4"). Enter the PIN slowly in se-
quence and confi rm the entry with the "OK"
button (61). The control functions will be unlo-
cked and the lock LED (51) will light up green.
- If you have entered an incorrect PIN, the lock
LED (51) will light up red. Press the "OK" but-
ton (61) to delete an incorrect PIN and then
enter the correct PIN afterwards.
Lock
If you wish to lock the control panel (2), press the
"4" button / lock button (65).
Standard PIN: New PIN:
1 2 3 4 _ _ _ _
Changing the PIN
To change the PIN, proceed as follows.
1. Unlock the control panel.
2. Press the "4" button / lock button (65) and the
"OK" button (61) at the same time. The lock
LED (51) will fl ash red and green alternately.
3. Enter a new PIN (four digits). Press the "OK"
button (61). The lock LED (51) will fl ash
green.
4. Enter the new PIN again and press the "OK"
button (61). The lock LED (51) will light up
green and stay on permanently. The PIN has
now been successfully changed.
5. Important! Make a note of your new PIN.
Requesting your PIN if you lose it
Have the receipt and the serial number of the
robot lawn mower ready. You need them in order
to get your PIN.
1. Connect a USB stick to the USB connection
as shown in the illustration. (Fig. 11).
2. Switch on the main switch (7) (ON).
3. Press the POWER button (60) and the "OK"
button (61) at the same time. Keep the but-
tons pressed for 3 seconds. All the LEDs (50,
51, 52, 53) on the control panel will now have
come on (2).
4. Press the "SET WORK TIME / 1" (62) button.
Anl_FREELEXO_Kit_500_SPK9.indb 39 Anl_FREELEXO_Kit_500_SPK9.indb 39
GB
5. Pull out the USB stick. Import the data from
the USB stick to a computer. A text fi le (*.txt)
will have been created by the robot lawn
mower. This fi le contains a PUK, a personal
code. Please contact the customer services
team to obtain your PIN.
6.5 Control of the robot lawn mower
Setting the mowing time
1. Unlock the control panel (2).
2. To select the desired mowing time, keep pres-
sing the "SET WORK TIME / 1" button (62)
until you have the setting you want.
3. The time is shown by the time LEDs (50).
4. To confi rm the setting, press the "OK" button
(61).
The time at which the changes were made is
now the daily starting time. The number of hours
shown is the daily work time.

Starting procedure

1. Unlock the control panel (2).
2. Press the "START / 2" button (63) fi rst.
3. To confi rm the starting procedure, press the
"OK" button (61).
The robot lawn mower will now operate in ac-
cordance with the mowing time setting. The batte-
ry charge level is monitored during the work time
and displayed via the battery LED (52). Whenever
the battery charge level drops to 30%, the robot
lawn mower automatically returns to the charging
station (19).
Stopping mowing
1. To bring the robot lawn mower to an immedia-
te stop, press the STOP button (3).
2. Unlock the control panel (2).
3. Press the "HOME / 3" button (64) followed by
the "OK" button (61) to send the robot lawn
mower along the perimeter wire (18) and
back to the charging station (19).
- 39 -
14.11.2019 12:22:52 14.11.2019 12:22:52