Setting Into Operation - Monacor TVCCD-150COL Mode D'emploi

The camera has an automatic gain control (AGC),
an automatic electronic shutter (
backlight compensation, and an automatic white
balance (range 2400 K to 11 000 K).
4 Mounting
1) The camera module in the dome can only be
panned around a small angle within the visual pro-
tection window. To find the optimum mounting place
and alignment of the camera, a trial run must there-
fore be made. For this purpose set the camera into
operation for the time being according to chapter 5.
2) Remove the dome with the visual protection from
the base (2): Turn the dome a quarter of a round to
the left up to the stop so that it disengages and can
be removed.
3) Mark the four mounting holes and the hole for the
connection cable and drill.
4) Tighten the camera with screws.

5 Setting into Operation

1) Connect the BNC inline jack (3) of the camera to
the jack TO CAMERA (13) of the power supply unit.
For this purpose a 75 Ω coaxial cable for video sig-
nals is required. When using a high-quality cable,
the cable length may be up to 500 m:
Cable Type Max. Cable Length
RG-58U
RG-59U
RG-6U
Up to 350 m the following cables from MONACOR
are suitable:
VCC-59, VCC-59/SW, VCC-59/WS, VCC-259/SW
2) Connect the video output VIDEO OUT TO MONI-
TOR (12) of the power supply unit via a 75 Ω
coaxial cable to the video input jack of the monitor
or a camera switcher or video splitter. Observe the
correct 75 Ω termination.
3) Connect the plug of the mains cable (9) to a socket
(230 V~/50 Hz) and switch on the power supply unit
with the switch POWER (8). The power LED (7) will
light up.
4) Switch on the connected monitor as well and pre -
cisely align the camera module to the surveillance
zone:
– for tilting, release the two knurled screws (5) and
retighten them after the alignment.
– for panning, release the two screws (4) in the
base. For this purpose the camera module which is
held by the knurled screws (5) must be unscrewed.
The camera module can only be panned around a
small angle, otherwise the visual protection blocks
up the sight.
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
1 1
/ – / s), a
50 100 000
200 m
350 m
500 m
® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
– If the picture should be twisted on the monitor,
turn the camera module around the axis of the lens.
For this purpose release the screws (6) and re -
tighten them after the alignment.
5) By turning the lens (1) adjust a clear picture repro-
duction on the monitor.
6) If required, modify the video output level by means
of the four sliding switches VIDEO GAIN ADJ. (11)
on the rear side of the power supply unit (see the
following table). This will compensate level loss by
a long connection cable between the camera and
the power supply unit.
Switch position
VIDEO GAIN ADJ.
OFF +
OFF +
OFF -
OFF -
OFF + OFF
OFF + OFF
or
OFF - OFF
OFF - OFF
OFF +
OFF +
OFF -
OFF -
OFF + OFF
OFF + OFF
or
OFF - OFF
OFF - OFF
OFF +
OFF +
OFF -
OFF -
7) Finally place the dome with the visual protection on
the base (2) in such a way that after turning (to the
right) to engage the dome, the camera is capable of
viewing through the visual protection window.
6 Specifications
Image sensor: . . . . . . . . . . 8.5 mm (
Colour system: . . . . . . . . . PAL
Synchronization: . . . . . . . . hor. 15 625 Hz,
Number of pixels: . . . . . . . hor. 752 × vert. 582
Resolution: . . . . . . . . . . . . 480 lines
Lens: . . . . . . . . . . . . . . . . . 1: 2.0/3.6 mm
Minimum illumination: . . . . 0.05 lux
S/N ratio: . . . . . . . . . . . . . > 50 dB (AGC off)
Video output: . . . . . . . . . . . 1 Vpp/75 Ω
Ambient temperature: . . . . -10 °C to +50 °C
Power supply: . . . . . . . . . . 230 V~/50 Hz/5 VA
Dimensions, weight
Camera: . . . . . . . . . . . . . Ø 87 mm × 53 mm, 260 g
Power supply unit: . . . . . 106 × 44 × 96 mm, 600 g
Subject to technical modification.
Output level
without cable loss
1.2 Vpp
+
+
1.3 Vpp
-
-
1.4 Vpp
+
+
1.1 Vpp
-
-
1.0 Vpp
1
/ ") CCD chip
3
vert. 50 Hz
GB
7