Programme Sequence; Premature Programme Abort; Cleaning And Maintenance; General Instructions - Dreve EyeVolution MAX Mode D'emploi

EyeVolution
®

7.3 Programme sequence

Each time program starts up with the
intensity of the LEDs reduced by 50 %
to ensure polymerisation is as tension-
free as possible. The LEDs automatically
switch to 100 % output after 30 s.
Important: In order to protect
your eyes, polymerisation is only
possible when the device cover
is closed.
The light used is not suitable for direct
eye contact and can cause retinal dam-
age over the long term when unfiltered.
The cover features a light-filtering
inspection window (13) to facilitate
visual inspection of the polymerisation
process.

7.4 Premature programme abort

An on-going time programme can be
ended and deleted at any time by press-

8. Cleaning and maintenance

Always remove the mains plug from the
mains power supply before carrying out
any cleaning or maintenance work.
Ideally, the device is cleaned using a
soft cloth, possibly a slightly dampened
sponge and a mild resin-cleaning agent.
24
MAX
An on-going time programme is always
interrupted by opening the cover (12);
the LED assigned to the respective
programme flashes. The time remain-
ing is saved in the electronics module
and continues once the polymerisation
chamber is closed again.
Once a time programme is complete,
2 brief signal tones sound and the
polymerisation LEDs and rotary motor
switch off automatically. The green
LED indicating the programme on the
operating foil (3) is also deactivated. A
ring of 6 white LEDs stays active and
is only dimmed down after the device
cover is opened.
ing the activated programme key.
Water and cleaning agent must not
penetrate the device.
The LED circuit board (9) must not
come into contact with damp materi-
als. Minor soiling can be removed using
a soft brush.

9. General instructions

Repairs and maintenance work on - operation is only by qualified personnel.
the EyeVolution MAX polymerisation - the device is used in accordance with
®
device may only be carried out by these operating instructions.
qualified personnel. In any case, the - extensions, new settings, modifica-
power supply to the device must be tions or repairs are only carried out
interrupted. The Dreve Group is only by persons authorised by Dreve Den-
responsible for the safety, reliability and tamid.
performance of the device when: As we constantly strive to develop our
- the device is only used for the corre- products, we reserve the right to make
sponding designated application technical modifications.

10. Disposal of old appliances pursuant to WEEE regulations

The EU Directive 2002/96/EC for the reduction of the increasing quantities of waste
from electric and electrical equipment (WEEE). The aim is to avoid and reduce the
increasing quantities of waste from electric and electrical equipment and to dispose
of such waste in an environmentally friendly manner. Appliances labelled accordingly
must not be disposed of with household waste, but correctly disposed of at communal rubbish
dumps, by your specialist dealer or the manufacturer.

11. Warranty

Responsibility for defects
The warranty period is 2 years as of
the delivery date. The warranty only Claims for defects shall expire one
applies for material or manufacturing year after delivery. Claims for defects
errors. Warranty claims do not apply do not apply for natural wear or dam-
for natural wear or damage incurred age incurred after the transfer of risk
after the transfer of risk as a result of as a result of incorrect or non-desig-
incorrect or non-designated handling, nated handling, excessive strain, unsuit-
excessive strain, unsuitable operating able operating equipment and such
equipment and such chemical, electro- chemical, electro-chemical or electri-
chemical or electrical influences which cal influences which are not intended
are not intended by the contract. War- by the contract. Claims for defects are
ranty claims are excluded by any non- excluded by any non-designated modi-
designated modifications made by the fications made by the customer, third
customer, third parties or maintenance parties or maintenance and repair work
and repair work as well as in the event as well as in the event of violation of
of violation of lead seals. lead seals.
25