14_Assembling The Suito-T; For Ø5 L=130 Mm And L=135 Mm Chainstays; 16_Installing The Bicycle On Suito-T; With Ø12 L=142 Mm Chainstays - Elite Suito-T Mode D'emploi

EN

14_ASSEMBLING THE SUITO-T

- Unpack the SUITO-T (A)
- Place the SUITO-T (A) in a vertical position and hold it in
place with the upper handle
- Unfold the right leg until the safety locking mechanism
clicks (Pic 1)
- Unfold the left leg until the safety locking mechanism clicks
(Pic 2)
- Make sure that the hometrainer is stable (Pic 3) or
alternatively adjust its feet (Pic 4).
15_INSTALLING THE SPROCKET CASSETTE
ON THE SUITO-T FOR Ø5 L=130 MM AND
L=135 MM CHAINSTAYS
- Assemble the sprocket cassette on the freehub by ali-
gning the groove profiles.
- 2 spacers (Ref. B) are usually needed for the Shimano
/ SRAM ® 9 speed cassette (Pic. 5), 1 spacer for the 10
speed cassette (Pic. 6) and no spacer is required for the 11
speed cassette (Pic. 7). Depending on the cassette brand
you are using there might be some differences with the
aforementioned general data.
- Using the torque wrench, tighten the lock ring supplied
with the cassettes onto the freehub body (Pic. 8).
CAUTION!
Strictly follow the instructions provided by the cassette ma-
nufacturer with regard to specific installation techniques,
the need for additional spacers and torque specifications.
NOTE: please contact your dealer if you have questions or
are unable to install the cassette. The warranty does not
cover any damage to the bicycle and/or SUITO-T in the
event of incorrect installation.
On bikes with 130-135 mm (5,1 -5,3 inch) chainstay you
must insert the right chainstay adapter (Ref. D) (Pic. 9) ) and
the left adapter (E) (Pic. 10). However, on bikes with ø12 mm
(ø 0.47 inches) thru-axle and 142 mm (5,6 inches) chainstay
please check paragraph 17.

16_INSTALLING THE BICYCLE ON SUITO-T

- Loosen the bike's rear brake and place the chain on
the smallest rear sprocket and the largest front chainring.
Remove the quick release from the rear wheel.
- Remove the rear wheel from the bicycle.
- Insert the quick release and the dropout adapter (Ref. C) on
the SUITO-T sprocket cassette (Pic. 11A-11B).
- Place the bicycle chain onto the smallest sprocket of
SUITO-T (Pic 12).
- Fully fit the bicycle's rear dropouts onto SUITO-T's cassette
(Pic. 13), paying careful attention to the correct internal or
external position, based on the type of bicycle:
44
- External triangle adapter (Ref. C) for road and time trial bikes
(130mm triangle) (Pic.14).
- Internal triangle adapter (C) for mountain bikes (135mm
triangle) (Pic. 15).
NOTE: the knurled side of the triangle adapter (Ref. C) must
be facing the bicycle dropout.
- Securely fix the bicycle to SUITO-T and firmly close the
quick release. The resulting pressure should keep the bicycle
dropouts locked to the SUITO-T.
- Make sure the bike is perfectly vertical once installed.
WARNING: the dropout of the bicycle must be leaning on the
edges of the adapter and not on the Quick Release.
Elite shall not be liable for any damages that might arise from
an improper assembly of the bicycle on the hometrainer.
17_INSTALLING THE SUITO-T ON BICYCLES
WITH Ø12 L=142 MM CHAINSTAYS
®
1) Insert the left adapter (Ref. G) and screw the rigth adapter
(Ref F) for 142mm carriages (Fig. 16);
2) Loosen the rear brake of the bicycle and place the chain
on the smallest sprocket of the rear wheel and the front
chainring. Remove the thru-axle from the rear wheel.
3) Position the bicycle's rear dropouts on the axle of the
sprocket cassette of the SUITO-T.
4) Insert the thru-axle on the SUITO-T sprocket cassette shaft.
5) Make sure the bicycle is safely positioned on the SUITO-T
and lock the thru-axle with a strong push. The pressure
should make the bike dropouts remain locked onto the
structure of the SUITO-T.
6) Make sure the bike is stable by pushing and pulling the
top tube of the frame and the saddle. Should the bike still
be moving a little on the SUITO-T, use more force to lock
the thru-axle.
7) If you wish for more bicycle stability it's advisable to use the
provided Riser block (Ref I) to be placed under the front wheel.
- Start pedalling. Ride very slowly at first and increase your
speed gradually until you become familiar with the features of
SUITO-T.

18_POWER SUPPLY

- SUITO-T feature electronic circuitry inside and is powered
up by a standard power supply (included).
Insert the power supply in the electrical outlet and the jack
plug in the connector on the back of the SUITO-T (Pic. 17),
a slight vibration indicates that the system is adjusting to its
initial position. This can last up to 15 seconds.
Place the cable inside its housing in the rear of the
hometrainer and hook it in the edges in the lower area of the
rear plastics (Pic. 18)
The SUITO-T compliance with EU laws (see "Declaration of
conformity", page 119) may be voided if a charger different
from the original is used.